Q4: NGO i- CLO 4 - P1-14 A boat is propelled by a steam turbine. The moment of inertia of the rotor, shaft and propeller is 60 kg.m. The turbine runs at 3000 rpm in clockwise direction looking from the front. The boat describes a circular path towards the right making one revolution in 10 s. 1. Check the magnitude and direction of the couple acting on the boat hull, 2. Evaluate the effect of gyroscopic couple on the boat.

Q4: NGO i- CLO 4 - P1-14 A boat is propelled by a steam turbine. The moment of inertia of the rotor, shaft and propeller is 60 kg.m. The turbine runs at 3000 rpm in clockwise direction looking from the front. The boat describes a circular path towards the right making one revolution in 10 s. 1. Check the magnitude and direction of the couple acting on the boat hull, 2. Evaluate the effect of gyroscopic couple on the boat.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Paragraf Stiller Düz 11 In Figure 2, the wheel with mass p (kg) with an inertial radius of kA (mm), M-X.t (N.m) it has been subjected to moment (t seconds). Starting from a stationary state calculate the angular speed of the wheel after t1 seconds. Also, the reaction force that the fixed bearing a exerts on the wheel during movement calculate. (Gravity acceleration will be taken as 9.81 m/s2.) kA= 252 mm p= 13 kg x= 3 t;=2 M Odak
The system shown in the figure consists of two masses attached to a massless road and rotates about the vertical axis at O. The system initially rotating freely at the angular speed of 140 rad/s, when a constant couple moment of CO= 8 Nm is applied on the direction shown.a) Find the time required to stop the assembly.b) Calculate the number of revolutions made until the system stops
A single cylinder reciprocating engine has speed 240 rpm, stroke 300 mm, mass of reciprocating parts 60 kg, mass of revolving parts at 200 mm radius is 37 kg. If three-fifth of the reciprocating parts and all the revolving parts are to be balanced, find: the balance mass required at a radius of 500 mm, and the residual unbalanced force when the crank has rotated 60° from top dead center. 28.00 kg, 3481.74 N 20.33 kg, 1406.76 N 25.13 kg, 2637.68 N 21.94 kg, 1899.13 N 29.20 kg, 4220.29 N
Now consider two very similar semi trucks. One travels at 40 km/hr and another travels at 75km/hr. Which truck will have the greater motion inertia?
Gravitational acceleration g = 10 m/s? 1. A uniform thin rod of length Im and mass m,od = 20 Kg in the figure can rotate freely in the plane about an axis at 30 cm from one of its ends while the other end attached with a disk of radius 10 cm and mass maisk = 10 Kg. As the rod swings from the angle 30". a. Find the position center of mass. b. Calculate the moment of inertia for the composed system. c. What is the velocity of the disk while reaching an equilibrium point? 30 cm
A sphere of mass M and radius R is not necessarily solid or hollow. It has moment of inertia I= cMR2. As shown in the figure, the sphere starts from rest and rolls without slipping down a ramp from height H. It then moves back up the other side, but now with no friction at all between the sphere and the ramp. What height does the sphere reach?
A flywheel weight = 50 kN with radius of gyration= 1 m losses its speed from 400 rpm to 280 rpm in 5 minutes. Find change in angular momentum.
A solid bar of mass m and length L stands vertically on a frictionless table and is then released to fall down. The moment of inertia about the center of mass is Ic = mL²/12. At the moment when the top end B just reaches the ground (0-0), (a) what are the angular velocity and angular acceleration? (b) what is the center-of-mass acceleration? (c) what is the normal force of the ground to end D? Hint: It may be helpful to find out the instant rotation axis. В m. L D
The mass of a propeller is 4.5 tons and its centre of gravity is 3.5 mm from the centre of rotation. Find the pull due to centrifugal force when it is rotating at 120 rev/mm
I need a clear and fast answer within 20 minutes. Thank you
HW4 A ship has its turbine engine mounted with its axis of rotation lengthways in the ship. When viewed from the back, the engine rotates anticlockwise at 3500 rev/min. The effective rotating mass of the engine is 200 kg with a radius of gyration of 0.4 m. Calculate the magnitude of the gyroscopic couple produced when the ship turns left on a radius of 200 m with a velocity of 3 m/s. Explain clearly the effect of the couple on the motion of the ship.
Q4/. A commercial airfiner with four jet engines, cach producing 120 kN of forward thrust, is in a steady, level cruise when engine number 3 suddenly fails. Determine and locate the resultant of the three remuining engine thrust vectors. Treat this as a two-dimensional problem. 120 KN 120 AN 120 KN Figure.4