Q4/ In the following figure, the first resistance (R1 = 202) and the second resistance (R2 = 1002), calculate: 1- The value of the resistance (R4) when the bridge is in equilibrium (V1 = V2) and the value of the variable resistance (R 3 = 502). %3D 2- The value of the variable resistance(R3)when it is(V1 = 3V2). %3D

Q4/ In the following figure, the first resistance (R1 = 202) and the second resistance (R2 = 1002), calculate: 1- The value of the resistance (R4) when the bridge is in equilibrium (V1 = V2) and the value of the variable resistance (R 3 = 502). %3D 2- The value of the variable resistance(R3)when it is(V1 = 3V2). %3D

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

The Wheat stone Bridge circuit is used to measure the unknown resistance Rx. At balancecondition, R1= 581ohm, R2=100ohm and R3= 743ohm. Determine the unknown resistance?(CLO1/PLO4)
it's urgent please solve asap
P1 Is P2 Vs = P3 VA Value Powers Value Sources PRI Pr2 1250.000 mw Vs 10 V 1250.000 mw Is 0.500 A PR3 1250.000 mw Find V4
How do find the equivalent resistance of multiple resistors configures in parallel? You sum the resistances together and then divide by the number of resistors You average all of the individual resistor values. You calculate: 1/ (1/R1 + 1/R2 + + 1/Rn) ... You use the smallest resistor value.
Refer to the following circuit diagram. Find the current Is1 supplied by source E₁. and current Is2 supplied by E2. E₁ 130V Ist A Z₁ 3352 N Z₂ 1052 B D Z₁ 2402 Z 502 C Isz E₂ 110V
Use the Principle of Superposition to determine the current i through R3 in the Figure. Let R1 = 100, R2 = 40, R3 = 20, R4 = 20, R5= 20, Vs 10 V, Is = 2A. ww VS R3 ww www
Referencing to the components connected on the breadboard below, draw the equivalent circuit schematic. 24 V R3 • . . o .. • . o o .. R4 • . O O 0 O O o o O o o O. O o o o o O o o o O o o Oooo o o OoO • 0 o o O0 o o o o o 0 Oo O O o o O o
3Draw the circuit diagram an solve using ohms law asap pls 3. Two lamps rated 100W and 200V areconnected in series across 200V supply . Find the power consumed by each lamp
This Homework is too much... i already solved 3 question but still alot to go.. Please Help me Solve this.
Shown in the figure below is an electrical circuit containing three resistors and two batteries. I₁ 0= 4 + L . ww R3 R₂ ww 1₂ R₁ ww Write down the Kirchhoff Junction equation and solve it for I, in terms of I₂ and I3. Write the result here: 1₁ = 12-13 R₂=552 R₂ = 132 13 Write down the Kirchhoff Loop equation for a loop that starts at the lower left corner and follows the perimeter of the circuit diagram clockwise. - IzR3 − LR₁ + 14 + 10 Write down the Kirchhoff Loop equation for a loop that starts at the lower left corner and touches the components 4V, R₂, and R₁. 0 = 4-1₂R₂-11R₁ The resistors in the circuit have the following values: R₁ = 12 Solve for all the following (some answers may be negative): I₁ = 27.78 X Amperes 1₂ = 28.84 X Amperes 13 = 1.060 X Amperes NOTE: For the equations, put in resistances and currents SYMBOLICALLY using variables like R₁,R₂,R3 and 11,12,13. Use numerical values of 10 and 4 for the voltages.
Help me please
Q1) Using suitable circuit analysis method, determine V1, V2, V3 and V4 of circuit in Figure Q1 below. V4 20 Q 10 Q V1 10 V2 10 Q 30 Q V3 4 A 20 Q Figure Q1