Q4: Determine the minimum transmission bandwidth required to transmit the following two signals: fi(t) = 10 cos 150 at + 15 cos 200 nt and f2(t) = 10 cos 100 nt cos 200 nt in a PAM/TDM system. Compare the result if FDM is used with AM & SSB techniques.

Q: . What is the highest decimal munher that can be represented by each of the following nanbers of…

A:

Q: What is the advantage and disadvantages Static and Dynamic characteristic of measuring instruments.…

A: Step-1->Static and dynamic characteristics are two important aspects of measuring instruments.…

Q: hich of the following can’t be included in data required for coordination study? A)X/R ratio B)MVA…

A: characteristic curves of the fuses and breakers are generally analyzed in the coordination study

Q: How to use Ni Multisim?

A: The NI Multisim is an easy-to-follow and simulated place for engineers, students, and professors who…

Q: The static characteristics of the measurement instrument are act

A: In this question, The static characteristics of the measurement instrument are act....?

Q: The cathode of a device is generally marked, it is indicative of: a. The positive terminal of the…

A: The cathode of a device is generally marked.

Q: Which of the following layer is below the drift layer in non bunch through IGBT ? O a. p-layer O b.…

A: The IGBTs without n+ buffer layer is called as non-punch through IGBTs.

Q: 304. How does a TRIAC differ from a SCR? please don't use A solution

A: SCRs are unidirectional devices where triacs are bidirectional. An SCR is designed to switch load…

Q: b. Check the below statements and state whether these statements are true or False. Justify your…

A: knee voltage is a voltage at which the value of the forward current increasing rapidly.

Q: With neat diagram explain the construction and working of CRO.

A:

Q: ckt diagram of refrigerator

A: In refrigerator, split single phase induction motor is used to run the compressor unit. Compressor…

Q: 21 54 ZA 22 28 23

A:

Q: What is a Semiconductor? Explain the properties of a Semiconductor such as its physics, etc?…

A: There are various kinds of materials depending on the properties of these materials. In electronics…

Q: Consider an n-type semiconductor, in which minimum conductivity design criteria is applied. Select…

A: Given data:The semiconductor is of n-type.Minimum conductivity design criteria are…

Q: Answer the following questions. 1. What is ceramics? 2. Give some examples of Ceramics products. 3.…

A:

Q: a) Explain FOUR (4) measurement standards available.

A:

Q: Skin effect impact O a. the frequency of the TL O b. the current of the TL Oc. all of the other…

A: In AC power systems the skin effect or skin effect losses are referread as the losses due to flow of…

Q: tronic components definitions and si units and color coding

A: Electronic components : There are mainly two type of Electronic components one is active Electronic…

Q: Find the value of (1ti).

A: The complex number Can be solved easily.

Q: 1. What is the difference between a conductor and a semico 2. Which element is used to construct…

A: In this question we will write about semiconductors, conductors and doping... Note :- as per our…

Q: Explain the elements of measurement system in detail

A: Measurement system : measurement system is combination of various component which measures the…

Q: S We measured the current that appeared on the plotted screen as shown in the figure by means of…

A: The most popular form is the D'Arsonval galvanometer, which uses a light coil of wire strung from a…

Q: Which of the following are n-type semiconductors? Please choose one: a. Negative charge b. None of…

A: we will solve this by checking every option .

Q: Q3/ Count 5 only from Types of Registers. Briefly.

A: To count 5 only from types of registers

Q: 10. What is the duty cycle (percentage) of a signal if TON equals TOFF?

A:

Q: An electrical component has a reliability of 0.95 over 1,500 hours of normal use (note normal use…

A: Given  Reliability = 0.95  Usage in hours = 1500 Here the electrical component usage indicates it…

Q: 1.List the three steps of nuclear fuel fabrication processes. Also sketch a schematic diagram and…

A:

Q: 2) Explain with diagram and waveforms the ASK demodulation .

A: 2) This ASK type of modulation or demodulation goes under Digital Modulation plans. Here, the word…

Q: All electronic components are formed from p type and n type materials. What factors determine what…

A: In p-type semiconductors, holes are the majority carriers and electrons are the minority carriers.…

Q: Insulators Are porcelain discs which are non-porous, free with impurities and cracks that prevents…

A: According to the question,Insulators are porcelain discs which are non-porous, free with impurities…

Q: Select which elements are usually used as impurities for n-type semiconductors.

A:

Q: Summarize on how testing is carried out on isolators and circuit breakers of high voltage system.…

A: The Electric power demand is rising rapidly. Now a days, Huge quantity of electrical power is needed…

Q: Shackle type insulators are used for voltage in the order of  ....................... Complete the…

A: Given  Shackle type insulators are used for voltage in the order of  .......................

Q: find the Volume of ' . holloww shell. d 1952M mo

A:

Q: If a Si diode at room temperature (25°) has a leakage current IS = 56 nA, k = 5,800, and VD = 0.58…

A: Given, Is=56nAk=5800VD=0.58V And, the temperature is: T(oC)=25oT(K)=25+273=298K

KVL and KCL

KVL stands for Kirchhoff voltage law. KVL states that the total voltage drops around the loop in any closed electric circuit is equal to the sum of total voltage drop in the same closed loop.

Sign Convention

Science and technology incorporate some ideas and techniques of their own to understand a system skilfully and easily. These techniques are called conventions. For example: Sign conventions of mirrors are used to understand the phenomenon of reflection and refraction in an easier way.