Q4: Design a ladder logic program to run the three Motors:(Y0= oil pump motor, Y1 = auxiliary motor, Y2= main motor)according to the following information:The ON/OFF sequence of all three motors should be as per tablegiven below. The sequence should continue till start input is present.In addition, stopping all motors immediately when STOP is pressed.Motors ON/OFF Sequence TableTime In SecondsMotors0-55-1010-1515-2020-2525-30YOONONONOFFOFFOFFY1OFFOFFSONONSONOFFY2ONOFFOFFOFFONONOIL MotorAuxillary MotorMain MotorPage 3 of 3START XOSTOP X1

Here's a ladder logic program that runs the three motors (Y0 = oil pump motor, Y1 = auxiliary motor,…

Answered: Q4: Design a ladder logic program to…

Electricity for Refrigeration, Heating, and Air Conditioning (MindTap Course List)

10th Edition

ISBN:9781337399128

Author:Russell E. Smith

Publisher:Russell E. Smith

Chapter8: Basic Electric Motors

Section: Chapter Questions

Problem 46RQ: Explain the operation of the direct current motor used in mini-split units.

See similar textbooks

Similar questions

Please solution to this assignment
23. In a DC servo motor system, the tachometer feeds back a voltage that's proportional to motor speed. Where does this voltage go to? A. The driver B. The interpolator card C. The axis logic card D. The CPU in the main controller xis logic card for a stepper motor system and are used to
Pls help me answer the following questions . I promise I will up vote you.
The amount of short-circuit current from a motor is equal approximately to_current for each motor. A.accelerating b. locked-rotor c. stator d. final
Question 4 1. State the four programming languages described in the IEC 61131-3 standard. (4) 2. A simple motor latching circuit has the following I/O: Inputs: StartPB %10.0 N.O. momentary action push button StopPB %10.1 N.C. momentary action push button Overload %10.2 N.C. K1 Aux %10.3 N.O. Auxiliary feedback contact from motor. Outputs: K1 Coil %Q0.0 RunLamp %Q0.1 Motor Contactor Coil K1 Motor Run Indicating Lamp StopLamp %Q0.2 Motor Stopped Indicating Lamp Sketch a program to control the motor using any two of the IEC61131-3 languages. Include a latch mechanism. You must use all the inputs and outputs. Include both the label and memory addresses on your program. (8) 3. A Human Machine Interface (HMI) must be added to a Programmable Logic Controller (PLC) that controls a conveyor. The PLC program is shown on Figure 4a. The machine operator must be able to start and stop the conveyor via the HMI and be aware of the status of the conveyor i.e., running/stopped. Network 1: Conveyor…
Obtain the analysis (state table and state diagram) of the synchronous sequential circuit in the figure below. What structure does the circuit have from Moore and Mealy type machines?
Answer all the following questions:
lo 4) obtain the analysis of the synchronous sequential circuit (State table and state diagram) in the figure below. What structure does the circuit have from Moore and Mealy type machines? 8 Q1 Or FF FF 4. 01 K1 R
What is the fundamental frequency of the following variable speed drive signal? +Volts -Volts frequency 25 Hz frequency3KHz O a. None of the choices O b. 1500 Hertz O c. 50 Hertz O d. 3000 Hertz ○ e. 25 Hertz
Urgent need answer
Write general information about sequential timer for DC motor control
A stepper motor is configured in to a half step. If it rotate 32 steps. what data pulse is the last fed on the wires if the pulse starts with 1000? Select one: a.1010 b.0110c.1000 d.1100 e.0101

SEE MORE QUESTIONS

Recommended textbooks for you

Electricity for Refrigeration, Heating, and Air C…

Mechanical Engineering

ISBN:

9781337399128

Author:

Russell E. Smith

Publisher:

Cengage Learning