Q4/ A rectangular plate 3 m long and 1 m wide is immersed vertically in water in such a way that its 3 mside is parallel to the water surface and is 1 m below it as shown in Figure 2.22. Find (a) Total pressure onthe plate (b) Determine the total pressure at the base of the plateFree water surfaceheb=3mC

Given data:Length of plate, L=3mWidth of plate, b= 1m.Area of plate , A=L×B=3m2we also know,…

Answered: Q4/ A rectangular plate 3 m long and 1…

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The plane rectangular gate, as shown in Figure 13, can pivot about the support at B. For the conditions given, is it stable or unstable? Neglect the weight of the gate. Justify your answer with calculations. (Unstable)
Calculate (a) the elongation of the copper wire when the 50 KN vertical force is applied at and (b) the vertical displacement at load P. Copper Wire A = 500 mm? L= 1.30 m E = 120 GPa P= 50 KN В A O 3.20 m 1.80 m
A circular aluminum column 6 m long has a diameter of 200 mm. Determine the critical load if one end is recessed. E = 73 GPa. σY = 250 MPa.
SECTION: 300 mm 10 KN m 800 mm A B 15m P= 300 KN e= 250 mm A. Calculate the stress at the top located in the centerline of the beam. (MPa) Calculate the stress at the bottom located in the centerline of the beam. (MPa) В.
A closed tank has several layers of liquid and a circular bottom.a. Determine the hydrostatic force acting on the circle plug of the tank. b. Determine the distance of this force from the top. 2.e cm= 2.2 cm 1.f = 1.0 cm
1. The rigid gate with 3m width is installed in order to control the water outflow as shown in the figure. The gate is hinged at point O and rests against a support at point B. Assuming that the weight of the gate as well as the friction at the hinge don't have significant effects, determine the following: Wate 4 m a. Determine forces (resultant forces). b. Locate the center of pressure for the hydrostatic forces (resultant forces). c. Required horizontal force, the gate closed. the magnitude of the hydrostatic Hing 3 m B A P in order to hold 2 m Atmosphere
Probl A closed tank filled with water is rotated about a vertical axis. D=4 ft, o= 10 rad/s. Find: Pressure at bottom center of tank (psig). Properties: p= 62.4 lbm/ft³ = 1.94 slug/ft³, y = 62.4 lbf/ft³. 4 ft diameter P=? 6 in HILJ 12 in 4 12 in 1 ft —
A simply supported rectangular aluminium plate has a length a = 5.0 m; and a width b = 2.0 m. It is designed to carry a lateral pressure of 6 MPa. Take E = 120 GPa, v= 0.27, oy = 280MPa and p=2700kg/m³ Determine The minimum required thickness h of the plate(consider the factor of safety n = 1.5); The fundamental frequency of the plate.
Moment (KN.m) 300 250 200 150 100 50 0 0 A Moment-Curvature Relation 0.01 0.02 0.03 0.04 0.05 0.06 0.07 Curvature (1/m) L b) Yield displacement (Ay). Ay= Calculate the following values: a) Yield Force (Fy) that will cause the system to yield at point A. Fy= c) Plastic displacement (Ap). Ap= Hint: Au Ap+Ay = Başka yönergeler almak için tıklayın For the cantilever beam system given, construct the relation between the force (F) and the displacement (A) of the free end. You need to transform the moment curvature relation given into force-displacement relation. Beam length: L = 3.5 m Plastic hinge length: Lp = 0.3 m Note: All the results are positive. F e) The ultimate (failure) force (Fu) Fu = d) Ultimate (failure) displacement (Au). Au= (m) 0.08 0.09 (m) F A ha Ay Au (KN) (Write 2 digits after the decimal point) (m) (Write 4 digits after the decimal point) (Write 4 digits after the decimal point) (Write 4 digits after the decimal point) A (KN) (Write 2 digits after the decimal point)
Stress transformation based
From the figure below, assume 2 K1 =1.2 K2 = 2.7 K3 = 3 K4 and that layer 2 and 3 are of equal heights. AB = 8 cm, BC = 12 cm and CD = 10 cm. All remaining units are also in cm. A K2 K1 K4 K3 a. Determine the pressure head at point B in m. (IN 2 DECIMAL PLACES) b. Determine the pressure head at point C in m. (IN 2 DECIMAL PLACES) c. Determine the rate of flow in cm^3/s if K1 = 3.5 x 10^2 cm/s (IN 2 DECIMAL PLACES) 28
2-71. Determine the resultant force acting on the triangular plate A and the location of the center of measured from the free water level in the tank. Solve the pressure, problem using the formula method. b) Solve Prob. 2-71 using the integration method. 5 m 1.8 m 1 m m

SEE MORE QUESTIONS

Recommended textbooks for you

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Fundamentals of Structural Analysis

Civil Engineering

ISBN:

9780073398006

Author:

Kenneth M. Leet Emeritus, Chia-Ming Uang, Joel Lanning

Publisher:

McGraw-Hill Education

Sustainable Energy

Civil Engineering

ISBN:

9781337551663

Author:

DUNLAP, Richard A.

Publisher:

Cengage,

Traffic and Highway Engineering

Civil Engineering

ISBN:

9781305156241

Author:

Garber, Nicholas J.

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS