Q4) A 220 V, d.c. shunt motor has an armature resistance of 0.4 2 and a field resistance of 220 2. When driving a load of constant torque at 500 r.p.m., the armature current is 15 A. If it is desired to raise the speed from 500 to 700 r.p.m., what resistance should be inserted in the shunt field circuit? Assume that the magnetic circuit is unsaturated.

Q4) A 220 V, d.c. shunt motor has an armature resistance of 0.4 2 and a field resistance of 220 2. When driving a load of constant torque at 500 r.p.m., the armature current is 15 A. If it is desired to raise the speed from 500 to 700 r.p.m., what resistance should be inserted in the shunt field circuit? Assume that the magnetic circuit is unsaturated.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A 141 V, DC separately excited motor drives a variable torque load TL = 0.01 N at 1150 rpm speed. The armature and field resistances are 0.3 N and 150 N, respectively. The motor draws a line current of 10 A at the given load. If rotational losse is equal to Prot = 0.1 Pin, the following questions. answer 1- Calculate the armature voltage to reduce the speed by 55%. V, =( V M1 2- Calculate the armature Vt Vf voltage to operate the motor at the holding condition. Ea V V 3- Calculate the efficiency of the motor at rated condition. % 4- Calculate the efficiency of the motor for part 1. 7 = %
Suppose that we are designing a 1200-rpm dc motor to run from a 240-V source. We have determined that the flux density will be 1 T because smaller fluxes make inefficient use of the iron and larger fluxes result in saturation. The radius of the rotor (and thus, the torque arm for the armature conductors) is 0.1 m. The lengths of the armature conductors are 0.3 m. Approximately how many armature conductors must be placed in series in this machine?
A 400 V series motor has a field resistance of 0.02 ohm and an armature resistance of 0. 1 ohm. The motor takes 30 A of current at 1000 rpm while developing full load torque. What is the motor speed when this motor develops 60 % of full load torque and the shunt is shunted by a resistor of 0.03?
4-pole DC in series motor, 180 Nm torque. The coil is wavy, at 600 total conductors, and the magnetic flux per electrode is 0.02 Weber. The resistance of the product and log windings is 0.2 ohm and 0.1 ohm, respectively. Calculate the copper knob if the reciprocating force generated is 205 volts
In a spinning industry, a 205 V, 6 pole shunt motor runs at a speed of 1250 rpm gives an output of 7 HP with an armature current of 38 A. The armature winding is wave connected and it has 690 conductors. Its armature resistance is 0.3 and drop at each brush is 1 V. Find (i) Useful torque, (ii) Total torque, (iii) Useful flux per pole and (iv) Rotational losses occurring in the motor. [ 1HP= 746 W]
A 4 pole d.c. motor takes a 38.6 A armature current. The armature has lap connected 350 conductors. The flux per pole is 15 mWb. Calculate the gross torque developed by the armature of the motor. Also calculate Torque if flux per pole changes to 18 mWb and state difference in torque from 18 mWb to 15 mWb
A 4 pole10V, DC shunt motor operates on a load current 10A, having wave connected armature with 200 conductors. The flux per Pole is 25 m Wb. Resistance of shunt field winding is 1 ohm and resistance of the armature is 0.15 ohm. a) what would be the back emf?
Q4 A 220 V shunt motor has an armature resistance of 0.5 N and take armature current of 40 A at full-load. By how much must the main flux be reduced to raise the speed by 50 % if the developed torque is constant?
Q2) Determine the back e.m.f at this load of series motor has a series field resistance of (0.301 2) and an armature resistance of (0.1892).It is connected to a (220 V) supply and at a particular load runs at (1500 r.p.m) when drawing (16.2 A) from the supply, if that this cases a three times of flux. Calculate the speed of motor when the load is changed such that the current is increased to (32.23 A).
In a spinning industry, a 225 V, 8 pole shunt motor runs at a speed of 1450 rpm gives an output of 8 HP with an armature current of 32 A. The armature winding is wave-connected and it has 780 conductors. Its armature resistance is 0.1 Q and drop at each brush is 1 V. Find (i) Useful torque, (ii) Total torque, (iii) Useful flux per pole and (iv) Rotational losses occurring in the motor. [ 1HP= 746 W] Useful Torque Total Torque Flux per pole Rotational Loss in the Motor
a 220 V dc shunt motor has armature resistance 0.23 ohm, on load it takes armature current 40 A and turnes at 720 rpm, if the flux of motor is reduced by 10% without changing the load torque . Find the new speed of the motor.