Q(3):Draw the construction details of a cantilever beam supported by one column to Scale 1:10 if: 1- Clear span = 2.8m. 2- Supporting columns dimensions are 40 x 60cm. 3- Beam width = 40cm 4- Beam depth = 70cm at support end and 45cm at free end. 5- Tension Reinforcement: 5bars Ø20mm (one layer). 6- Compression Reinforcement: 2bars Ø16mm 7- Stirrups Ø12mm @ 20cm in the first half part of span (near support) and @ 30 cm in the second half part of the span (one pace). 8- Concrete cover = 4cm.

Q(3):Draw the construction details of a cantilever beam supported by one column to Scale 1:10 if: 1- Clear span = 2.8m. 2- Supporting columns dimensions are 40 x 60cm. 3- Beam width = 40cm 4- Beam depth = 70cm at support end and 45cm at free end. 5- Tension Reinforcement: 5bars Ø20mm (one layer). 6- Compression Reinforcement: 2bars Ø16mm 7- Stirrups Ø12mm @ 20cm in the first half part of span (near support) and @ 30 cm in the second half part of the span (one pace). 8- Concrete cover = 4cm.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Compression Steel Given: The beam cross-section shown have the following cross-sectional properities: f'c = 4000 psi Find phi Mn.
= ======= == Q2- The architectural engineer proposed a width of 350 mm and a height of 750 mm for a cantilever beam shown below, as you a design engineer ,design this beam according to ACI-14 requirements and assume in your solution that: Mu 1300 kN.m fc 21 MPa and fy 420 MPa Bar diameter of 32mm for longitudinal reinforcement. Bar diameter of 12 mm for stirrups. Two layers of reinforcement for both tension and compression zone. ⚫Use bundle bars when it is possible. 350mm
1.13 The section shown in Fig. 3.34 represents a beam in a structure containing prefabricated elements. The total width and total depth are limited to 350mm and 530mm respectively. Tension reinforcement used is four $28 bars. Using fe-28 MP and fy=420 MPa, determine the design moment strength of the section. 65 465 100 125 100 350 125 8 = 0.003 N.A. + 0.85fc T=A,fy T z=d-y
1. For the given singly reinforced beam section, fy =352 MPa, and f's = 28MPA. Calculate the required parameters for the different section condition in the table. d = 257mm h = 307mm 200mm Concrete Steel of Location Limit for No. of 16mm Area of diameter bar Condition Depth strain strain compression of block "a". neutral steel in to meet the axis "c". sq.mm. given beam condition. Units N/A N/A mm mm Sq.mm bars Balanced 0.003 Condition Compression 0.003 controlled Transition 0.003 controlled Tension 0.003 controlled
Calculate the design bending strength for the doubly reinforced rectangular section where A’s = 2500 mm2 f’c= 30 MPa & fy = 350 MPa if As =8500 mm2
need asap. please be detailed with your solution and box the final answer.
Find the maximum allowable value of P for the column. The cross-sectional areas and working stresses (ow) are shown in the figure. |2P Steel: A = 500 mm2 Ow = 120 MPa P Timber: 4P A = 2000 mm? Ow = 12 MPa Concrete: A = 8000 mm? O = 16 MPa
show complete solutions and answer should be in 4 decimal places
Use USD method.
Given a concrete column that would be required to support loads of Pu=400kips and Mu=50 kip-feet, we will determine the column interaction curve and decide if the column is adequate for this particular application. The column will be a 14”x14” square, tied column with #9 bars at the corners. The center of the reinforcement in each corner is 3” from each of the sides. The f’c of the concrete is 4 ksi and the reinforcement is Grade 60. Determine if the column is acceptable for this application. Calculate the value of Mu and Pu.
Problem No. 3 A beam 200x45Omm is reinforced by 2-32mm diameter rebar. Assume cc=50mm, stirrups=10mm, fc'=21Mpa and fy=415Mpa. Calculate the following. 17. Calculate the strain of the steel reinforcement 0.00182 O 0.00201 O 0.00224 0.00391 O 0.00577