Q3/A/ Write the micro operation for the control word 1.01001100100101 2.01000000000000 3. 10000010011000
Q: What does a switch statement use to determine the current state of a state machine? O A case…
A: Given What does a switch statement use to determine the current state of the state machine?
Q: Control word is 11100111000101 Please answer part A only.
A: Ans:) AS per the instructions I am solving only part 1, and the given control word is 11100111000101…
Q: Using the Arduino set/emulator, create a program with three LED lights: red, green and yellow. Each…
A: Program1 // variables int GREEN = 2; int YELLOW = 3; int RED = 4; int DELAY_GREEN = 5000; int…
Q: Write down the micro-operations corresponding to the following control words: 4. CO4 (a) (b) (c) (d)…
A: Hey there, I am writing the required solution of the above stated question.Please do find the…
Q: A- Refer to the program and addresses in the diagram below. Explain how the output (O:4/6) would be…
A: ANSWER:-
Q: Q3/ B/ Write the control word for the micro operation 1. R6 + R6 + 1 2. R4 E R4 V R5
A: Due to bartleby guidelines, i can solve only 1 part of the questionIf you want the answer of the…
Q: a processor has 75 signals whie s shown below 15 can be saved by using Vertical
A:
Q: Q:Find the control word to the * - following instructions control word CW= SUB R1, R2 R1 – R2 → R1
A: It is a word where each but represents the various control signals. It is also said to be an…
Q: What is correct instruction if you want the control to go to the location 2000h? A MOV 2000h B MOV…
A: Question. What is correct instruction if you want the control to go to the location 2000h? A MOV…
Q: Exercises: 1- Write the micro operation for the control word: 11010011101100
A: The control word is a composition of four selectors required to select register and operation of ALU…
Q: Q5: Write down 82C55 Control word that set Port A, Port B, and Port C Lower as output in mode 1, and…
A: The answer for the above mentioned question is given in the below steps for your reference.
Q: In 8085 Assembly Language, write a program that does the following The operand specifies the 1/0…
A: Assembly language programming in 8085: A processor's assembly language is unique to that processor.…
Q: Assume G1 is a 32-bit unsigned global variable. We wish to write code that increments G1 if G1 is…
A: // Type your code here, or load an example. int incr(int num) { int g1=8; while(g1<32){ g1=g1+1;…
Q: byte sayi1=0xF0; byte sayi2 = 0xAB; byte temp; temp = (byte)(sayi1 | sayi2); Console.Write(temp +…
A: A bitwise OR operator(|) is binary operator, the output of bitwise OR is 1 if at least one…
Q: An 8-bit variable can count numbers from 255 to 0 of the AT328P microcontroller. It will send to the…
A: include<reg51.h> void delay(int value ){int i,j; for(i=0;i< =value;i++) for(j=0;j<…
Q: (Bug Binary addi Svo, Szero, 0 loop : Iw $v1, 0(Sa0) sw $v1, 0($a1) addi $a0, Sa0, 4 addi $a1, Sa1,…
A: Here, we have to convert MIPS instruction to machine code.
Q: Q3/A/ Write the micro operation for the control word 1.01001100100101 2.01000000000000 3.…
A: The micro-programmed control unit uses micro-instructions to generate the control signal.…
Q: What are the control signals for bne? A. RegWrite=0, ALUSrc=SignExtend, ALUOP=Mutliply, MemWrite=1…
A: Answer is given below .
Q: What will be the value of ECX when the following sequence of instructions has executed? push 5 push…
A: What will be the value of ECX when the following sequence of instructions has executed? push 5 push…
Q: A section of code to M control is transferred when a processor is interrupted is known as explain
A: A segment of code to which control is moved when a processor is interrupted is known as M. A field…
Q: For keyboard input, when the user depresses a key, this generates an electronic signal that is…
A: False is the correct option
Q: Which type of I/O processing is most efficient? a. Boolean b. Polling c. Logic d. Interrupt
A: Answer; Option d Interrupt
Q: After the following instructions are performed, what is the result in A? MOV R1, #21h DEC R1 MOV A,…
A: MOV R1,21H // mov 21H into R DEC R1 //Decrease R value by 1 means become 20H MOV A,R1 // mov R1 to A…
Q: Q3/ B/ Write the control word for the micro operation 1. R6 5- R6 +1 2. R4 E R4 V R5
A: Solution:
Q: Q3/A/ Write the micro operation for the control word 1.01001100100101 2.01000000000000…
A: The micro-operation for the most part occurs in the CPU of the PC. these are low-level directions…
Q: h- Write a program to control four traffic lights of four streets intersection using the…
A:
Q: What is the value of accumulator (Acc.) and flag register after :executing the following program MVI…
A: Answer: option4 Accumulator: A=AA , Flag =00
Q: Write a C++ code which takes a input from the user a time in the seconds then convert that time in…
A: 1- In this assignment, take the second input from the user, based on the input calculate the hour,…
Q: The accumulator contains F2H, Copy A into memory 8000H. Also copy F2H directly into 8000H.
A: ANSWER:
Q: 4. Write the C code for the given comments. The clock speed is 3 MHz. //Set up Port 2 Pins 2,3,7 as…
A: The basic idea is to use your SysTick wait function to create a digital output signal on P1.0. When…
Q: void setup() { pinMode(8, OUTPUT) ; } void loop() { digitalWrite(8, HIGH) ; delay(500) ;…
A: Dear Student, 10 Hz means a delay of 1/10 sec as we know that delay(1000) causes a delay of 1 sec…
Q: Q3/ B/ Write the control word for the micro operation 1. R6 + R6 +1 2. R4 E R4 V R5
A:
Q: During a l/0 read: [select all that are true] The address flows in to the MPU RD =0 The address is…
A: RD - Read : This is a Read control signal (active low). This signal indicates that the selected I/O…
Q: The Arduino instruction that will give you the state of a switch or push button is: digitalWrite() O…
A: pinMode
Q: Basic Looping using emu8086 Display sets of "*" based on the user's integer input (0-9). Output:…
A: The question has been answered in step2
Q: Write instructions that jump to label L1 when the unsigned integer in DX is less than orequal to the…
A: Instruction for the given statement: JBE is the jump instruction that is used for unsigned integer…
Q: Frequency Division __________________ Access is Better known as _______________.
A: This fill in the blank question is asking for frequency access in computer science.
Q: void setup() { pinMode (13, OUTPUT); } void loop() { digitalWrite(13, HIGH) delay(1000);…
A: Given that Aurdino function . pinMode() Function The pinMode() function is used to configure a…
Q: 5 write command byte for 8255 if Port A input, port B output, Port C output the mode2 of operation
A: I will explain it in details,
Q: Q3/ a- Write a program to control the 5 devices as input port A, and output port B. using the…
A: Output stack variables
Q: Ten hex numbers are stored in RAM locations 50H onwards. Write an 8051(microcontroller) C-program…
A: MOV R0, #50H MOV R1, #10H MOV B, #0 BACK: MOV A, @R0…
Q: Make a python program that asks the user to enter a six digit pin before proceeding to the menu (see…
A: Prompt for PIN and if PIN matches then only show the available options and use an if conditional…
Q: Write the sequence of control steps required to add a number to the Accumulator(AC) when the number…
A: The term addressing modes alludes to the manner by which the operand of a guidance is indicated. The…
Q: Q3/ B/ Write the control word for the micro operation 2. R4 E R4 V R5
A: Solution:
Q: Connect an LCD and a KEYPAD to 8051. Write a program to read an unsigned number from the keypad(…
A: Solution As the conditions is given in the question, here is the required code. #include…
Q: Divide two numbers inputted by the user in EMU8086.
A: Ans: Algorithm:: start with N1, N2, and set some A to -1. increment value of A. subtract value N1…
Q: Identify the status of accumulator after each line of the program in EMU8086 MOV AX,23H MOV BL,45H…
A: - The question is to identify the status of the accumulator after each line of the microprocessor…
Q: What value will be in the D accumulator after the following instructions have executed? 1daa #-100…
A: ldaa # -100 ldab # 100 mul so here we have to find the value of accumulator D and we have to…
Q: This is MicroController Question, it's about PIC18F452* Comment on the following uncommented…
A: The code is again written here after mentioning all the comments for the different lines. To check…
Step by step
Solved in 2 steps with 2 images
- Write down the micro-operations corresponding to the following control words: 4. CO4 0110000000011110 0011011100111101 0100000000100100 (d) (e) 1101100001101011 1111011001010010Exorcises: 1- Write the micro operation for the control word: 11010011101100 2- Write the control word for the micro operation: R6 R6 +1Exercises: 1- Write the micro operation for the control word: 11010011101100
- A(n) __________ is a storage location implemented in the CPU.Write a Code in Assembly Language that increments number from 0 - 120 on-screen with a delay of 1 sec. and the increment is seen on the window as the value changes. Code must run on dos box. Print Num code should be used to print the number7- In C, to make the first 4 bits port C as input port and the last 4 bits (Most significant) as output, the following command is used: O TRISC=0x003; OTRISC=0X0F; O PORTC=0x00; OPORTC=0X0F; 8 converts analog signal to digital signal so the microcontroller can work with or process that signal. OUSART OFlash memory CADC OTimer
- If this code runs from its start until the endpoint, the value in register edx will be: S0x1, tedx Sox8, tecx Ox40106e : mov Ox401073 : mov Ox401078 : test Secx, tecx Ox40107a : Ox40107e Ox40107c : jmp Ox40108a Ox40107e : lea (secx, tecx, 1),teax Ox401081 : lea (šeax, sedx, 1), teax Ox401084 : lea Oxffffffff (šeax), sedx Ox401087 : dec šecx Ox401088 : jmp Ox401078 : // endpoint Ox40108a 1) 45 2) 55 3) 65 4) 75Exercises: 1- Write the micro operation for the control word: 11010011101100 2- Write the control word for the micro operation: R6 R6 +1The effective address of an operand is the value of its actual address in memory.True or False.
- Encode the following R-format instructions: . and x30, х28, х29 . or x5, х31, х4 . хor x9, х9, х8 Encode the following I-format instructions: • andi x3, x30, 79 . ori x5, х31, 31 . xori x7, х7, 0What value will be in the D accumulator after the following instructions have executed? ldaa #-100 ldab #100 mul Invalid results because 8-bit multiply is only valid for unsigned numbers. Zero. -100 100 -10000 -1000For any wrong input display INVALID INPUT Sam it would be:---.