Q3/A solid circular shaft is subjected to a bending moment of 3000 N.m and a torque of 10000 N.m. The shaft is made of 45 C 8 steel having tensile stress of 116 MPa and a shear stress of 83 MPa. determine the diameter of the shaft.

Q3/A solid circular shaft is subjected to a bending moment of 3000 N.m and a torque of 10000 N.m. The shaft is made of 45 C 8 steel having tensile stress of 116 MPa and a shear stress of 83 MPa. determine the diameter of the shaft.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: A compound shaft is made by mounting a brass sleeve on a steel shaft (which is considered as…

Q: A 6-splined shaft delivers a torque of 7.5 kN - m. The spline has the following dimensions: D = 75…

A: given; →torque(T)=7.5KN-m =7.5*106N-mm→outer diameter(D)=75mm→inner…

Q: Design the outside and inside diameters for a hollow stell shaft subjected to a torque of 1,000,000…

A: Given data: The torque applied is, T = 1,000,000 lb-in. The shear stress developed, τ = 8,000 psi.…

Q: A compound shaft consists of brass segment (1) and aluminum segment (2). Segment (1) is a solid…

A: The allowable shear stress for brass shaft, The allowable shear stress for aluminum shaft, The value…

Q: A solid circular shaft of diameter 100 mm is subjected to an axial stress of 50 MPa. It is further…

A: Given:Torque, T=10 kN-mDiameter of the shaft, d=100 mmAxial stress, σ=50 MPa

Q: In Figure 2, the shaft is made of a solid A992 steel at section AB (ra = 25 mm), Ti-6A1-4V titanium…

A: r1=15mmr2=20mmr3=25mmT=120N-md1=30mmd2=40mmd3=50mm To-Find:- Resultant Angle of twist at D

Q: 3.10 The stepped steel shaft carries the torque T. Determine the maximum allow- able magnitude of T…

Q: The aluminum shaft, composed of three segments is fastened to rigid supports as A and D. Calculate…

Q: A solid shaft 2 inch in diameter is subjected into two torques .If the total angle of twist is eight…

A: Givend=2inT1=200 lb ft=200×12=2400 lb in

Q: Find the diameter of the solid shaft. Torque = 190 kNm Maximum shear stress = 210 MN/m2

A: Substitute the given values in the Maximum shear stress equation to get the diameter of the shaft.

Q: Torsion A hollow circular shaft has inside and outside diameters of 30 mm and 40 mm respectively.…

Q: The figure below show a stepped shaft in torsion. Compute the maximum shear stress at the step when…

Q: Solid shaft can resist a bending moment of 4.0 kNm and twisting moment 6.0 kNm together. Determine…

A: Given data, M= 4 kNm T=6 kNm Need to find maximum torque in shaft(Tm).

Q: n outside diameter of 70 m and :

A: here outer dia (70m) is >>>> inner dia (50mm). so the polar moment of inertia almost…

Q: Problem #1. The 60-mm diameter shaft is subjected to torques as shown. If the applied allowable…

Q: A hollow circular steel shaft with an outside diameter of 2.569, and a wall thickness of 0.388 in.…

A: GivenPart 1D=2.569int=0.388inT=292 lb-ftL=124inG=12000 ksiPart 2D=2.915int=0.437inT=239 lb-ftL=105…

Q: Let's consider a shaft having a diameter of 80 mm, subjected to the shown torques. Calculate the…

A: Givend=80mm

Q: 4 kN m 1.5 kN m Aluminum Steel Bronze B 100 mm 75 mm 3m 2 m 1.5 m- C FIG. P3.12 FIG. P3.11 3.12 The…

A: For solution refer below images.

Q: A solid circular shaft of diameter 60mm is subjected to an axial stress of 20 MPa. It is further…

Q: A solid shaft of circular cross section has a diameter of 15mm and is loaded by a torque of 130Nm at…

Q: L1=1.8 L2=.9 d1=70 d2=53 Compound shaft ACB is fixed at A and consisting of two solid circular…

A: Given data:-diameter, d1=70mm & diameter, d2=53mmLength, L1=1.8m=1800mm &…

Q: Compute the torsional shear stress (MPa) in a 45-in circular steel shaft with a diameter of 42-mm…

A: The length of the circular shaft, (L)=45 in.The diameter of the shaft, (D)=42 mm.The torque on the…

Q: ches and length 4.25 feet transmits 75 HP from an electric motor to a compressor. The allowable…

Q: an aluminum shaft is 6ft. and has toruq of 500 lb-ft. the shear stress is 6500 psi and the angle of…

Q: A solid constant-diameter shaft is subjected to the torques shown. The bearings shown allow the…

Q: À solid 0.96-in.diameter shaft is subjected to the torques shown. The bearings shown allow the shaft…

Q: A solid circular shaft of a diameter 100 mm is subjected to an axial stress of 50 MPa. t is further…

A: Given: d=100 mm σ=50 MPa T=10 kN-m

Q: Find the torsional shear stress on a 2 inch diameter shaft if it is subjected to a torque of 561…

A: Given diameter of shaft = 2 inch. Torque=561in-lb.

Q: The 70-mm-diameter solid shaft shown is subjected to torques of 600 N·m and 1400 N·m at points B and…

Q: Compute the torsional shear stress in a circular shaft with a diame to a torque of 800 N-m.

Q: A compound shaft consists of two pipe segments. Segment (1) has an outside diameter of 212 mm and a…

A: The outside diameter of the shaft for segment 1, D' = 212 mm = 0.212 m The wall thickness for…

Q: Solid shaft can resist a bending moment of 3.0 kNm and twisting moment 5.0 kNm together. Determine…

A: To Find: The maximum torque for the shaft. Given : The bending moment is M=3 kNm. The twisting…

Q: 2. The diameters of the solid shafts are: AB is 0.6 in, BC is 0.75 in. and CD is 0.9 in. The applied…

Q: Solid shaft can resist a bending moment of 8.0 kNm and twisting moment 10 kNm together. Determine…

A: Given data, For solid shaft, T=10 kNm M= 8 kNm Need to find maximum torque Tm

Q: A 1100 Nm torque is applied at B (CW looking from C towards A). Shaft (1) is solid brass with G 40…

Q: 2. The composite shaft of total length 1.8 m consists of 5 mm thick brass and is fixed to a 30 mm…

A: Given Data. →> Diameter of Steel Core = 30mm → Diameter of Brass jacket = 30+ 2(5) = 40 mm…

Q: 1. A shaft is made from AISI 1040 hot rolled steel with Su = 496 MPa, Sy = 290 MPa with 18%…

Q: aft with a hollow cross section is subjected to torque of magnitude T = 5.5 kN-m. If the outer…

A: Given:T=5.5 kN.mdo=0.1 mt=10 mm

Q: A solid 1.6 in. diameter shaft is used to synchronize multiple mechanisms in a manufacturing plant.…

Q: i need the answer quickly

Q: For the shaft in below, motor gives a 500 Nm torque on the shaft when it is rotation with a constant…

Q: The steel shaft of a socket wrench has adiameter of 8.0 mm and a length of 200 mm (seefigure).If the…

A: Given Data The diameter of the shaft is: d=8×10-3 m The length of the shaft is: L=200×10-3 m The…

Concept explainers

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.

Question

Q3/A solid circular shaft is subjected to a bending moment of 3000 N.m and a torque of 10000 N.m.
The shaft is made of 45 C 8 steel having tensile stress of 116 MPa and a shear stress of 83 MPa.
determine the diameter of the shaft.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A solid shaft is subjected to a twisting moment of 150 kNm. If the angle of twist is 8º per meter of the shaft and the shear stress is not to exceed 550 MPa. Determine the suitable shaft diameter by comparing the strength design and rigidity design. Also, determine the maximum shear strain acting on the shaft. Take G 250 GPa. Diameter of shaft based on Strength design is in mm Diameter of shaft based on rigidity design is in mm The sutable Diameter of the shaft is in mm The maximum shear strain is
A circular solid shaft has a diameter of 60 mm and is subjected to a torque load of 8.7 kN•m. Determine the resulting torque maximum and minimum shear stress.
id=6 k=1.2
A solid constant-diameter shaft is subjected to the torques shown. The bearings shown allow the shaft to turn freely. Determine the internal torque in segment (2) of the shaft. Assume that TA = 130 N-m, TB = 300 N-m, Tc= 365 N-m, and Tp = 195 N-m. X TD O -155 N-m -204 N-m O -170 N-m -230 N-m O-214 N-m Tc C (2) B TB (1) TA
A solid circular shaft is acted upon by thetorques as shown. If G= 12, 000 ksi determine:a. Rotation of wheel D with respect to A.b. Shear stress at point EDiameter of shaft:A-B = 2inC-D = 2inB-C = 4inT1 = 2.5 π in.kipsT2 = 8.5 π in.kipsT3 = 7 π in.kipsT4 = π in.kips
A compound shaft consists of two solid shafts that are connected at flange B and attached to rigid walls at A and C. The shafts are made of same material, having shear modulus G80 Gpa and different diameters di and de Determine the internal twisting moments at A Here di = 0.2 m, d₂ = 0.1 m. L₁ = 1 m. L₂ 1 m. M. 100 N-m. 4 Mo Select one: O 1. 60-70 N-m O 2. 80 – 90 N-m O3.70-80 N-m O 4.50-60 N-m O 5.90-100 N-m
A shaft made from acrylic is subjected to the three torques indicated below. The acrylic has a shear modulus of 1.7 GPa. Determine: a. The twist at the end D if the diameter if the shaft is 100 mm. b. The minimum shaft diameter if Tallow = 10 MPa 200 N•m A 800 N•m 300 mm B 400 N•m 600 mm C 600 mm
9. I upvote! Thanks!
A solid constant-diameter shaft is subjected to the torques shown. The bearings shown allow the shaft to turn freely. Determine the internal torque in segment (2) of the shaft. Assume that TA = 130 N-m, TB = 320 N-m, Tc = 371 N-m, and TD = 181 N-m. TD (3) O -208 N-m O -224 N-m O -138 N-m O -190 N-m O -265 N-m Tc (2) B TB (1) TA
The two solid shafts are connected by the gears shown. The motor constantly supplies 20 kW of power at 15 Hz to system at A. The yield shear stress is 140 MPa for shaft (1) and 220 MPa for the shaft (2), and over all factor of safety is 2. a) Find the diameter of both shafts. b) If the modulus of rigidity of shaft (2) G is 77.2 GPa, calculate the relative angle of twist D with respect to C. 30 teeth B (1) 48 teeth Tp 0.8 m
6. I upvote! Thanks!
A alm T 1.20 m T B 1.20 m C 3 T The 60 mm diameter shaft is made of 6061-T6 aluminum having an allowable shear stress of Tallow 80 MPa. Find the corresponding angle of twist of disk A relative to disk C. Note: You will need to calculate the maximum allowable torque T first. Provide your answer for angle of twist in radians with 3 significant figures after the decimal point.