Q3. The length of a column, having a uniform circular cross-section of 7.5 cm diameter and whose ends are hinged, is 5 m. If the value of E for the material is 2100 tonnes/cm ^2, the permissible maximum crippling load will be...

Q3. The length of a column, having a uniform circular cross-section of 7.5 cm diameter and whose ends are hinged, is 5 m. If the value of E for the material is 2100 tonnes/cm ^2, the permissible maximum crippling load will be...

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Problem 1 A spherical gas tank has an inner radius of r = 1.5 m. Part A If it is subjected to an internal pressure of p = 210 kPa, determine its minimum required thickness if the maximum normal stress is not to exceed 12 MPa. Express your answer to three significant figures and include the appropriate units. ANSWER: t =
Question- A hollow circular shaft has the diameters 50 cm and 30 cm and is subjected to a torque. If the realized maximum shear stress is 30 N/mm², what is the applied torque to nearest units? C P
Current Attempt in Progress Construct the shear-force diagram and identify the largest negative shear force. Assume a = 4.5 ft, b = 9.0 ft, c = 18.0 ft, w = 1170 lb/ft, and P = 3200 lb. P B C D a b. Answer: Vmin lb Save for Later Attempts: 0 of 1 used Submit Answer
A reinforced concrete column 500mm square in section is reinforced with four steel bars of 25mm diameter, one in each corner. The column is to carry load of 1000kN. Calculate the stresses in the concrete and steel bars. E steel=219X109N/m2 and E concrete =14X109N/m2
A 1060 kN cube (3m each side) floats in a 1.8m depth of water which is on top of the mercury layer. a. Determine the vertical distance from the top of the cube to the interface of water and mercury. b. If a load of 760 kN is added to the weight of the cube, what is the distance from the top of the cube to the water surface?
2.Determine the value of W if the 100kg crate is on the verge of tipping forward as it slides up the incline. Use d = Im. 0.6 m 1.8m fk = 0.2
Please answer correctly and box the final answer
Please provide solution with answers mentioned
Figure A 4.5 m Wo B. 1 of 1 1.5 m C Part A Determine the largest intensity wo of the distributed load that the beam can support if the beam can withstand a maximum bending moment of Mmax = 12 kNm and a maximum shear force of Vmax = 80 kN. (Figure 1) Express your answer with the appropriate units. Wo = Submit ☐ O µA Value Request Answer Return to Assignment Units Provide Feedback
2.Calculate the earth pressure acting on a concrete structure P Pa Lat Pat Lx1=4 M Ly1=8 M Lz=2 M Px1=14 N/m Px2= 8 N/m Py1=15 N/m
2. A CUBICAL FLOAT 1.2m ON A SIDE, WEIGHS 182kg AND IS ANCHORDED BY ME NS OF A CONCRETE IS TAUT, 22.5cm OF FLOAT ARE SUBMERGED. WHAT RISE IN THE WATER LEVEL WILL LIFT THE CONCRETE OFF THE BOTTOM ? CONCRETE WEIGHS = 2400 kg/m³. 1.2 H 86824 _WS
An engineer proposes as a solution to the problem of the dam, to reinforce it according to the figure shown, but now the critical height h of the water level must be determined, which would make the indicated concrete reinforcement on the verge of overturning due to the water pressure. The density of the concrete 2.40 Mg/m^3, H=18m and d= 6m. Hints: use typical values of water, consider one meter width of the dam to then generalize and don't forget point A.