[Q3] The following test results are obtained from a three-phase 60 hp, 2200 V, six-pole, 60 Hz squirrel-cage induction motor. (1) No-load test: Supply frequency = 60 Hz, Line voltage = 2200 V Line current = 4.5 A, Input power = 1600 W (2) Blocked-rotor test: Frequency = 15 Hz, Line voltage = 270 V Line current=25 A, Input power = 9000 W (3) Average DC resistance per stator phase: R1 =2.8 2. Determine the no-load rotational loss, stator current, P.F and efficiency.

[Q3] The following test results are obtained from a three-phase 60 hp, 2200 V, six-pole, 60 Hz squirrel-cage induction motor. (1) No-load test: Supply frequency = 60 Hz, Line voltage = 2200 V Line current = 4.5 A, Input power = 1600 W (2) Blocked-rotor test: Frequency = 15 Hz, Line voltage = 270 V Line current=25 A, Input power = 9000 W (3) Average DC resistance per stator phase: R1 =2.8 2. Determine the no-load rotational loss, stator current, P.F and efficiency.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

The armature winding resistance of a long shunt connected DC generator is 0.4ohm, the resistances of the shunt and serial field windings are 125 ohms and 0.1 ohms, respectively. While the generator supplies 8KW of power to the load it feeds, which is the voltage it produces since the output voltage is 250V?
The rotor of a 3-phase, 60-Hz, 4-pole induction motor gets a total of 120kW through the air gap with a rotor frequency of 3Hz. a. What is the rotor speed (RPM)? b. What is the rotor copper loss (W)?
Q2 Complete the answer : The rotor reactance of the three phase induction motor is varies with ................... of the rotor current.
A 3-phase, 50-Hz induction motor with its rotor star-connected gives 500-V(r.m.s.) at standstill between the slip-rings on open-circuit. Calculate the current and power factor at standstill when the rotor winding is joined to a star-connected external circuit, each phase of which has a resistance of 10 Q and an inductance of 0.04 H. The resistance per phase of the winding is 0.2 Q and its inductance is 0.04 H. Also, calculate the current and power factor when the slip-rings are short-circuited and the motor is running with a slip of 5 per cent. Assume flux remain constant.
A large 3-phase, 4160 V, 60 Hz, squirrel-cage induction motor draws a current of 400 A and the total active power of 2500 kW when operating at full-load. The corresponding speed is accurately measured and is found to be 1178 r/min. The stator is connected in wye and the resistance between two stator terminals is 0.15 0. The total iron losses are 26.5 kW and the windage and friction losses are 15 kW. Calculate the following: The power factor at full-load The active power supplied to the rotor The total I²R losses in the rotor The load mechanical power [kW], torque [kN.m], and efficiency [%] a. b. C. d.
The use of a series capacitor with the auxiliary windings of a single-phase induction motor permits: * The obtaintion a 90-degrees phase angle between currents in the main and auxiliary windings. The garantee a relatively high starting torque all above
What are the principle characteristics of DC series motor and DC compound motor, and what are its uses? Explain the Difference between Single Phase & Three Phase transformers with a Comparison Chart. What conditions are necessary for paralleling two synchronous generators?
2) A large 3-phase, 4000 Va (phase to phase), 60 Hz squirrel-cage induction motor draws a current of 385 A/phase. The total active power at the stator input terminals is 2344 kW, when operating at full load. The corresponding speed is accurately measured and found to be 709.2 r/min. The stator is connected in wye and the resistance between two stator terminals is 0.10 Q. The total iron losses are 23.4 kW and the windage and friction losses are 12 kW. Calculate the following: c) The total 1²-R losses in the rotor d) The load mechanical power (kW), torque (kN•m), and efficiency. S = Va · V3 - I S= Vy•3·I %3D
(Qld) A three-phase 20-pole induction motor is rated at 800 V, 50 Hz. What is the synchronous speed of this machine if the voltage at its terminals is reduced to 400 V (a) 150 rpm, (b) 300 rpm, (c) 600 rpm, (d) 3000 rpm
3. A 440V 60-hp six pole 60 hz A connected induction motor has the following parameters R1=0.048 R2= 0.035 Xm= 9.50 X1= 0.33 0 X2= 0.37 0 Pcore= 600W PF&W= 350W Use the Thevenin's Equivalent circuit concept to find: (a)Vth and Zth seen by the rotor circuit (b)The slip at which maximum torque occurs (c) the value of Max/pullout Torques (d) The starting torque.