Q3: The data for a wind turbine is given below: Wind speed = 14 meters/sec Length of blade = 20 meter Rotor efficiency = 50% Gear Box efficiency = 75% Generator Efficiency = 85% Calculate the power in the wind. Calculate the power output of wind turbine

Q3: The data for a wind turbine is given below: Wind speed = 14 meters/sec Length of blade = 20 meter Rotor efficiency = 50% Gear Box efficiency = 75% Generator Efficiency = 85% Calculate the power in the wind. Calculate the power output of wind turbine

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Water enters a fountain through a pipe with a cross-sectional area A1 at a flow rate Q. The pressure in the inlet pipe is p1. The water then leaves through a nozzle with a cross sectional area A2 and at an angle 8, as shown in Figure Q5. Both the inlet and the nozzle are at a height h2, and the jet reaches a maximum height 13. You may assume that viscosity is negligible. a) Find the horizontal force on the block b) What is the horizontal-component (u2), vertical component (v2) and magnitude (V2) of the velocity of the jet as it leaves the nozzle? c) What is the maximum height of the jet? You may assume that the horizontal component of velocity is the same at every point in the jet. P₁ A₁ A₂. To h₂ h3 Figure Q5: Jet emitting from a fountain.
A wind turbine, of radius 1.5 m, on a wind farm. If the wind speed is 8.0 m/s find the input and output powers if the efficiency of the system is about 25%.
8
-Q4:- If the wind speed measured on 10 m height from the earth. What the height of wind h? turbine tower should be if the turbine work on 5m/s. Discuss the height from the earth surface with roughness, if the surface are 1. Sandy surface is vary between (0.1-0.13). 2. Trees surface is vary between (0.2-0.25). 3. Hily surface is vary between (0.5-0.9).*
A large windmill design has a swept area of 1600m2. Assuming it operates at 100% of thetheoretical maximum for windmills, calculate its expected power :i) on Ovenden moor with a wind speed of 11m/s (average)ii) in Buckinghamshire with a wind speed of 3m/s (average)
4.27 A reaction turbine produces 5600 hp while operating at 260 rpm and a head of 60 ft. It is proposed to locate it in a place where the annual temperature variation is between 50°F and 108°F. What should the setting of the turbine be to avoid cavitation?
Example 3-6 A mixed type reaction turbine has D1= 3m and D1= 2.1m. Inlet and outlet Vane angle 60° & 150° respectively and thickness of 30 cm parallel to axis of rotation with guide vanes angle of 15° and a flow rate of 10 m/s . a) Calculate the required speed of the runner for smooth flow at inlet. b) If the velocity of flow remains constant and the discharge is radial find the power developed and the work done, also find the hydraulic losses, total head, and overall efficiency.
4.11 Verify the design of the San Francisquito power plant, which has the following specifications: P=32,200 hp, H=800 ft., N=171.4 rpm. Estimate the number of jets, if each jet is 14 in. in diameter. Ans: The wheel diameter is 176 in. and the number of buckets is 22. These val- ues are available in the public domain from the plant specifications.
A two-blade wind turbine is installed on top of a hill experiencing winds of up to 80 mile/h. Downstream of the propeller the wind speed is 50 mile/h. Assume ideal gas and standard condition for air and find the tip to tip diameter of the propeller to obtain a theoretical efficiency of 50%.
Q3) Kaplan turbine A) The runner of Kaplan turbine working under dsitance of (5.5m) to produce (9 MW). Speed ratio and flow ratio are (2.08) and (0.68) respectively. Overall efficiency is (0.85). Find diameter and speed of the runner. The hub to tip runner diameter is (1/3). Q4) Design of Kaplan turbine to work under a head of (25m) and transfer (10 MW) power the diameter of hub and tip are (1.2m) and (3m) and overall and hydraulic efficiency are (0.85) and (0.9) respectively. Find the speed and angles of velocity triangles. Hint: The velocity triangle of inlet and outlet radial flow
An irrigation line carries water from a lake down into an arid valley 810 ft below the surface of the lake. The water discharge through a nozzle with jet velocity of 220ft/s, the diameter of the jet is 4 in. Find the power loss in friction expressed in hp. (WITH FREE BODY DIAGRAM) CHOICES: A.127 B.120 C.158.45 D.187
Vacumm You are designing a vacuum system with a desired equilibrium pressure of 10-7 torr. The turbomolecular pump you are using has a pumping speed of 400 L/s. What is the maximium surface area of the chamber that you can allow, assuming that the outgassing rate per square cm 10-9 torr L/s? Note : total outgassing rate G = ( outgassing rate per area ) * ( area )