Q3 Show that, if the stator resistance of a three-phase induction motor is negligible, the ratio of motor starting torque T, to the maximum torque Tmax can be expressed as: T, Tmax 2 1 Sm Sm where sm is the per-unit slip at which the maximum torque occurs.

Q3 Show that, if the stator resistance of a three-phase induction motor is negligible, the ratio of motor starting torque T, to the maximum torque Tmax can be expressed as: T, Tmax 2 1 Sm Sm where sm is the per-unit slip at which the maximum torque occurs.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Q1 (a) Sketch the torque-speed profile of DC motor, induction motor, and synchronous motor. (b) Briefly describe the main components of load torque in electrical drives.
4 DECIMAL PLACES : 1. A single-phase motor has stator windings in space quadrature and is supplied with a single-phase voltage of 200 V at 50 Hz. The standstill impedance of the main winding is (5.2 + j10.1) and of the auxiliary winding is (19.7 + j14.2). Find the value of capacitance to be inserted inthe auxiliary winding for maximum starting torque.
Electric machine
) Discuss the relationship between the starting torque and supply voltage of rotating transformer with necessary equations ) A 6-pole, 3-phase induction motor operates from a supply whose frequency is 50HZ. Calculate: a) The speed at which the magnetic field of the stator is rotating. b) The speed of the rotor when the slip is 0.05. c) The frequency of the rotor current when the slip is 0.04.
The rotor of an 8-pole, 50-Hz, 3-phase induction motor has a resistance of 0.2 Q/phase and runs at 720 r.p.m. If the load torque remains unchanged. Calculate the additional rotor resistance that will reduce this speed by 10% [0.8 2] (City & Guilds, London)
A 50 Hz, six-pole, Y-connected, 400 V induction machine delivers 350 Nm to a load at 950 rpm. If we neglect the magnetizing losses and friction and windage losses, estimate the stator resistance if it is known that the efficiency at this point is 88% and the input power factor is 0.85 lagging. Stator Current Airgap power Stator Resistance
A DC series motor takes the current of 15A and terminal voltage is 220 V. The armature and field resistance is 2 ohms and 0.2 ohm respectively. If the field resistance is shunted by resistance which is same as field resistance value and current taken by motor is 12 A then back emf induced is (estimated time 2 minutes) a.194.8V b.198.4 V c.217.6 V d.200.3 V
A 420 Vdc, 8 pole Compound DC motor runs at 729 rev/min when drawing a load of 60 A from the supply when meeting a load demand of 28 kW. The compound motor has a Lap connected armature with 816 conductors. The Armature, Interpole, Series, and Shunt resistances are 0.295 Q, 0.0155 Q, 0.00118 Q, and 147 Q respectively. The series field has 6 turns per pole while the shunt field has 2800 turns per pole. Under full load conditions, the shunt current is 3.75 A, and the Friction and windage loss is Pf/w = 0.782 kW. Consider c =6 for lap winding. Assume constant shunt current and friction and windage loss, determine for a reduced output load of 14.5 kW; (a) The new armature current; (b) The new speed of the motor
The stator resistance of a 1-phase induction motor is 2.5 ohm and its leakage reactance is 2.0 ohm. Onno-load, the motor takes 4 A at 96 V and at 0.25 lagging power factor. The no-load friction andwindage loss is negligible. Under the blocked-rotor condition, the input power is 130 W at 6 A and42 V. obtain the equivalent circuit parameters.
1.
10. The rotor of an 8-pole, 50-Hz, 3-phase induction motor has a resistance of 0.2 2/phase and runs at 720 r.p.m. If the load torque remains unchanged. Calculate the additional rotor resistance that will reduce this speed by 10% [0.8 2 (City & Guilds, London)
A four-pole, three-phase induction motor drives a turbine load. At a certain operatingpoint the machine has 4 percent slip and 87 percent efficiency. The motor drives aturbine with torque–speed characteristic given by TL = 20 + 0.006ω2,where TL is theload torque at the shaft. Determine:(1) the torque at the motor-turbine shaft.(2) the total power delivered to the turbine.(3) the total power consumed by the motor.