Q3: Find the series inductance required to put a 200 kVA, 220 V/400 kV test transformer has 10 % leakage reactance and 2% resistance on 200 kVA base into resonance condition. An object has to be tested at 500 kV using the above transformer at 50 Hz. If the charging current of the cable at 500 kV is 0.5 A, neglect dielectric loss of the object. And Assume 8 kQ resistance for the inductor to be used Also find the input voltage, input power to the transformer and losses of test transformer?

Q3: Find the series inductance required to put a 200 kVA, 220 V/400 kV test transformer has 10 % leakage reactance and 2% resistance on 200 kVA base into resonance condition. An object has to be tested at 500 kV using the above transformer at 50 Hz. If the charging current of the cable at 500 kV is 0.5 A, neglect dielectric loss of the object. And Assume 8 kQ resistance for the inductor to be used Also find the input voltage, input power to the transformer and losses of test transformer?

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

What is band bending, and why does it happen when two dissimilar materials (for example, p-type and n-type semiconductors; metal and semiconductor) come into contact?
double clipper circuit Zener diodes 1N4733A has a voltage of 5.1 V and 1N4735A has a voltage of 6.2 V with a resistor R=300ohms has been used. you may like to increase the input to a 12 VRMS AC source in order to see the clipping at 7volt. Please, Do the theoretical calculations and plot the expected waveforms by hand. ( I have its multisim design and only needs theoretical calculation and hand drawn graph of it to compare to its data that I have collected from multism.) Thanks
Under short circuit, the reactance’s of the synchronous generator during the steady state condition are following, Leakage reactance(Xl)= 0.11 ohm and Armature reactance (Xad)= 0.7 ohm The direct axis synchronous (steady state) reactance (Xd) is
26. The reactance offered by a capacitor to alternating current of frequency 50Hz is 10ohms. If the frequency is increased to 100Hz, the reactance becomes _____ ohms. A. 5 B. 40 C. 20 D. 2.5
Using a positive Clamper with positive biasing voltage Circuit, with an AC voltage of Vi = 20v with a frequency of 60hz, a value of 500n for the Capacitor, a silicon diode, biased voltage voltage of 5 volts and a resistor with the value of 300 ohms. Find the current on the resistor at a simulation of 20ms in mA. Vm 2Vm R V,m Vo -Vm V, Input Waveform Output Waveform Positive Clamper with positive reference V, www
Intrinsic carrier concentration of pure silicon at 300 K will be .................?
how do i calculate the inverse capacitance and its uncertainty if the capacitance value 1.8748+/- 0.0006. please show steps im using this example to do my other values.
I need to solve the fifth point, please
For the given circuit below, a step down transformer gives an RMS voltage of 230 V/ 10.2-0-10.2 V with a load resistance of 2.2 Kiloohms. Assume Silicon diodes are used. Determine the Peak Inverse Voltage of the diode. D, SCT RL D. llle ண
.i. In a parallel plate capacitor, the cross sectional area of the plates are doubled and all other parameters remains the same. The ratio of Final capacitance to initial capacitance is found to be: