Q3)Consider the amplifier shown below. Assume R,-100 kW, Ra 30 kW, ß = 100, VT=25 mV and%3DVA=150V. Assume Vc=1.2V.a)Sketch the small-signal equivalent circuit of the amplifier. [20b)Find the input resistance Rin-Toc)Find the value of v. If v= 8 mv. [5Explain in your own words, what will happen in the performance of the amplifier if thebypass capacitor is removed. r ]d)+5 VRc=7 kaR =10 ka2 k-5 VwwHHww

Answered: Image /qna-images/answer/bd4283c6-fa9a-412c-8030-8c68e4240211.jpg

Q3) Consider the amplifier shown below. Assume R,-100 kW, R2 = 30 kW, B = 100, VT=25 mV and VA=150V. Assume Vc=1.2V. a) Sketch the small-signal equivalent circuit of the amplifier. [2d b) Find the input resistance Rin- T c) Find the value of vo If v, 8 mv. [5 Explain in your own words, what will happen in the performance of the amplifier if the bypass capacitor is removed. ro ] d) +5 V Rc=7 ka RI Cc 10 ka CE 2 k ww ww

Q3) Consider the amplifier shown below. Assume R,-100 kW, R2 = 30 kW, B = 100, VT=25 mV and VA=150V. Assume Vc=1.2V. a) Sketch the small-signal equivalent circuit of the amplifier. [2d b) Find the input resistance Rin- T c) Find the value of vo If v, 8 mv. [5 Explain in your own words, what will happen in the performance of the amplifier if the bypass capacitor is removed. ro ] d) +5 V Rc=7 ka RI Cc 10 ka CE 2 k ww ww

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Hello. Please can I have the correct solution to this Electrical Engineering problem in a step by step form. Thanks very much.
give short answer in 10 minutes i will give positive feeback
Do b)?
VoD +12 V For the circuit of the adjacent figure a) Given that Ip = 2.83 mA, VGS(om=-7 V and Ipss = 8 mA , find VDs and VGs.. b) If a 50 mV rms input signal is applied to the amplifier, what is the peak-to-peak output voltage? gm = 5000 µS. c) Calculate the output resistance. %3D Ro 10AF 0.1 uF R 10 L. Ra 10 MA 10kn ID= 2.83 mA, Vas (Oef)=-7V. %3D
Perform an ac analysis. Represent the amplifier by its ac equivalent circuit and discuss the input resistance at the base and the output resistance. (You can draw the circuit by hand on paper and can paste the image)
give short answer in 15 minutes i will give positive feeback
Four voltage sources of 3 V, 4V, 2V and 3V respectively are to be applied to the input terminal/terminals of “an" inverting amplifier. Design two different circuits for the two different cases with justified explanation and selection of proper resistances as per the requirements below: a) When an output of 4V is required (with phase shift). b) When an output of 8V is required (without phase shift) Note: Only inverting amplifier/amplifiers to be used for each case and all the voltage sources are to be used for each individual design as required in a) and b). 2.
Please solve with steps, using to study. Will upvote!
Note : Value of K1 = 17; K2 = 49 Show the each equation part and Mention ans same as asking in question. There are must be 2 graphs. Read the 2 pictures clearly and ans all the question. For Example : "Compare T+,T- , Draw the transfer characteristics V0 and V1 " Mention like this then ase the question. formula should be taken from "Operational Amplifier and Linear Integrated Circuits, by Robert F. Coughlin and Fredrick F. Driscoll, 6th Edition, Pearson." this book.
1. Calculate the following items related to practical op-amp circuit applications. a.) If the inverting amplifier circuit has R1 = 50 kN and R, = 370 kn, what output voltage results from an input of V, = 5v? b.) If the circuit has R1 = 75 kn and R, = 180 kN, what output voltage results from an input of V, = -1.7v? c.) Calculate the output voltage of a noninverting amplifier given the following values: V, 5v, Rf = 140 kN, and R1 %3D = 80 kN.
R7 lo Os The circuit in Figure 3 shows a simple multi-stage BJT op-amp, consisting of three different stages. It is given that for all transistors: B= 100, r,- 500 kN, g.-5 mA/V, and r-3 kn. (e) Determine the output resistance of the amplifier, R. ww-
1. Discuss the difference between Passive and Active Components? Give examples