Q3 An aileron painting station includes two conveyor belts, cylinder A for pushing objects on the painting table, the painting head B which operates with pressurized air, and cylinder C for removing the painted objects in 2 seconds. The conveyor belts operate continuously and transfer objects to and from the painting station. Therefore, they don't affect the automation logic. If an object is detected along the dashed line S from a corresponding proximity switch, the automation system must realize the position-step diagram shown in Figure Q3. After selecting the required additional pneumatic equipment (cylinders kind, directional valves, sensors, etc.): (a) Select and sketch the appropriate electro-pneumatic and I/O connection statuses for this painting station. (b) Assess the aileron painting station process and substantiate your evaluation with a PLC ladder program. B Paint spray gun Pressurized air flow Figure Q3 Aileron painting station

Q3 An aileron painting station includes two conveyor belts, cylinder A for pushing objects on the painting table, the painting head B which operates with pressurized air, and cylinder C for removing the painted objects in 2 seconds. The conveyor belts operate continuously and transfer objects to and from the painting station. Therefore, they don't affect the automation logic. If an object is detected along the dashed line S from a corresponding proximity switch, the automation system must realize the position-step diagram shown in Figure Q3. After selecting the required additional pneumatic equipment (cylinders kind, directional valves, sensors, etc.): (a) Select and sketch the appropriate electro-pneumatic and I/O connection statuses for this painting station. (b) Assess the aileron painting station process and substantiate your evaluation with a PLC ladder program. B Paint spray gun Pressurized air flow Figure Q3 Aileron painting station

Precision Machining Technology (MindTap Course List)

2nd Edition

ISBN:9781285444543

Author:Peter J. Hoffman, Eric S. Hopewell, Brian Janes

Publisher:Peter J. Hoffman, Eric S. Hopewell, Brian Janes

Chapter8: Computer Numerical Control

Section8.7: Cnc Milling: Setup And Operation

Problem 11RQ: What are the two controls on the machine's control panels that control jogging motion?

See similar textbooks

Similar questions

(3-d) Write down the sum-of-products expression that represents the output.
What does it mean to shift the patient into the treatment position? Could you describe the coordinate system used to shift the patient into treatment position.
pleasee Draw the simplified schematic diagram of the plant showing all the necessary data displayed on it
What are the two controls on the machine's control panels that control jogging motion?
After visualize the Robotic Mechatronic System draw the block diagram for thedifferent subsystem of a Mitsubishi Robots
#1. Hello can you find Ir1,ir2 ,Ireland, rt and it and pt. Thank you please show me how to do my homework
I want you to draw a ladder logic diagram of a garage door to control it by PLC. In my case we have different inputs and outputs and all of them gotta be used in the diagram. I can perfectly interpret the diagram so no need to explain it, I will just require you to draw it. INPUTS : open push button ( OPB ) - close push button ( CPB ) - open limit switch ( OLS ) - close limit switch ( CLS ) - obstacle detection sensor ( ODS ) - safety sensor ( SS ) - emergency stop push button ( ESPB ) - reset button ( RB ) OUTPUTS : motor starts ( MS ) - motor stops ( MSTP ) - motor forward ( MF ) - motor reverse ( MR ) - Error display ( ER ) OPERATİNG MODES : automatic mode ( AM ) - manual mode ( MM ) NECESSARY TIMERS : T1 ( delay door movement after obstacle detection ) - T2 ( delay door movement after reversing ) Here is my excercise for today. Please I am requiring a good logic diagram taking into consideration all what was mentioned before. so to sum up, I want you to write a logic ladder diagram…
a) Which type of control system is used in the given block diagram .Write the definition . Potentiometer Stepper to give a voltage signal motor Belt drive for the set Micro- Drive ADC processor circuit value of position Tool Feedback signal Potentiometer
For FANUC 6 axis robot How many E-stop buttons does the Fanuc robot system have? Where are they located?
Instruction: Give the step by step solution using autocad
A pick and Place machine is being used to transfer a box. The arm is extended (out) by energizing a solenoid valve; when the valve is de-energizes, the arm retracts (in). In the same way, a second valve closes the grip (when energized) or opens the grip (when de-energized). Here's a diagram of this "machine": Grip Air Cylinder Grip open Grip Closed Box Arm Air Cylinder Arm In Arm Out The system is really slow... it actually takes 3-4 seconds for the arm to fully extend. An engineer created the below diagram. Start Pressed Time (seconds) Box Falls - 1 -2 -3 - 4 - 5 -6 –7 -8 – 9 – 10 Extend Arm Close Grip Question (finally!). Which statement is completely true regarding this design? It uses the Master Clock scheme. Given this diagram, the arm will probably start to retract before the grip fully closes. O If the arm takes 4 seconds to retract (return), the box will be dropped "mid-flight" It uses the Domino Scheme. Things can't happen in the wrong sequence. It uses the Master Clock…
2 Sall Zal e Can the rudder be manually trimmed with the autopilot engaged? * The figure below is not true, because there are only one APU for each Airbus. aircraft * (i) O raise O e Both main generators and the APU generator are controlled by overhead associated pb sw.* O rase O me On the ground, the aircraft can be supplied by an external power urce only * O e The DC battery bus can charge the batteries or receive power from the batteries O Fase O me