Q#3: A steel Tape was exactly 30m long at 22°C when supported throughout its length under a pull of 10kg. A line was measured with this tape under a pull of 16kg and a mean temperature of 33°C and found to be 980m long. The cross sectional area of the tape was 0.035cm² and its total weight was 0.695kg. Coefficient of thermal expansion (a ) is 1lx10^-6/°C and modulus of elasticity is 2.1x10^6kg/cm² . Compute the length if the tape was supported during measurement. (i) At every 30m (ii) At every 15m

Q#3: A steel Tape was exactly 30m long at 22°C when supported throughout its length under a pull of 10kg. A line was measured with this tape under a pull of 16kg and a mean temperature of 33°C and found to be 980m long. The cross sectional area of the tape was 0.035cm² and its total weight was 0.695kg. Coefficient of thermal expansion (a ) is 1lx10^-6/°C and modulus of elasticity is 2.1x10^6kg/cm² . Compute the length if the tape was supported during measurement. (i) At every 30m (ii) At every 15m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

VECHANICS OF D. 5. 73.8% THERMAL STRESS Steel Rod d = 20 mm L = 5 m E = 200 GPa a = 11.70 µm/(m-°C) p = 8,000 kg/m³ 1. A steel rod is positioned vertically as shown in the figure. It is fixed at one end and unsupported at the other end. An external force (F = 800 N) is applied to the free end of the rod the same time when the temperature is raised by 25 C. Assume that all deformations will happen at the same time, compute the stress developed in the steel rod if the gap between the free end of the steel rod and the ground is 0.20 mm. %3D GAP
2 A rigid bar is supported by two copper ro ds and the gap (A) between the aluminu m rod and the bar is 1.50 mm. If the temp erature for all materials is increased by 4 0 degrees Celsius, what is the thermal str ess of the aluminum rod? Disregard the weight of the rigid bar. For each copper bar, A = 500 mm^2, E = 120 GPa, and a = 1 6.8 μm/(m. C). For the aluminum bar, A = 400 mm^2, E = 70 GPa, and a = 23. 1 μm/(m. C).(5 Copper Aluminum Copper 750 mm
A prismatic bar 50°F is imbedded in a rigid concrete wall. The bar is 40 in long and has a cross-sectional area of 4 in?. What is the axial force in the bar if its temperature is raised to 100°F? Assume cocfficient of thermal expansion is 5x10%F and modulus of clectricity is 32x10° psi.
A steel tape is 100 m long at a temperature of 20°C and a pull of 10 kg. It was used to measure a distance of 624.95 m at a temperature of 32°C with an applied pull of 15 kg during measurement with the tape supported at both ends. Coefficient of thermal expansion is 0.0000116/°C and a modulus of elasticity of 2x106kg/cm2. Weight of tape is 0.04 kg/m and a cross sectional area of 0.06 cm2. a) Compute the sag correction. b) Compute the total correction for tension, sag and temperature.c) Compute the corrected length of the line by applying the combined corrections for tension, sag and temperature
Solve the problem.
The steel plate shown below is put in into a rigid chamber, such that spacings of size s-000188 m. To fit the plate, it is heated. It can be assumed that the plate can move frictionless along its edges If x = 4 m and y- 2 m, E - 200 GPa V - 0.28 a = 11.7 x 10 ro When the upper surface of the plate is just about to close with the chamber due temperature increase along y-axis, how much is the stress on its side? Select the correct response 164.063 MPa 54.688 MPa 117.188 MPa
Three aluminum rods support the rigid L-shaped bracket BCF as shown in the figure. Determine the stress in each rod if rod FG is cooled by 50°C. All three rods have the same cross-sectional area of 1000 mm2. Use 73.1 GPa and 23 x 10-6/ °C for the modulus of elasticity and the coefficient of thermal expansion of aluminum, respectively. 2 m 1 m D 1.1 m B. 1 m 1.25 m 1.5 m
A 40mm diameter rod 6m long elongates 12mm under load of 240kN. The diameter decreasesby 0.028mm during the loading. Determine the following:a. The Poisson’s ratio of the material,b. The Young’s modulus of the material, andc. The modulus of rigidity of the material.
175 mm A 50 mm C -225 mm -300 mm Bar ACB shown in the Figure is subjected to a uniform temperature increase of 35°C. Knowing that the diameters of AC is 50 mm and CD is 75 mm, the modulus of elasticity E is 6.0 GPa, and the thermal expansion coefficient is 100x10^(-6) ?1/°C. What is the displacement of point C
The steel frame shown in Figure M-1 supports a rotating machine that exerts a horizontalforce at the girder level ?(?) = 200 sin 7.2? lb. Assuming 8% of critical damping, E = 29,000ksi and I = 75.3 in4, determine the following:Stiffness, ? = _____________________Frequency ratio, ? = _______________________Maximum Static Deformation, (???)? = _____________________Dynamic Magnification Factor, ?? = _______________________Steady-state Amplitude, ?? = _________________________
A line was determined to be 3,069.72 m when measured with a 50-m steel tape supported throughout its length under a pull of 5 kg at a mean temperature of 36°C. The tape used is of standard length at 20°C under a pull of 6 kg. Cross-sectional area of the tape is 0.04 cm 2 . Coefficient of thermal expansion is 0.0000116/°C. Modulus of elasticity of tape is 2x10 6 kg/cm 2 . Calculate the following: a. Error in the length due to change in temperature. b. Error of the tape due to tension. c. Corrected length of the line.
A steel rod of sectional area 25 sq. mm connects two parallel walls 5 m apart. The nuts at the ends were tightened when the rod was heated at 100°C. If Thermal coefficient of steel = 0.000012°C, Esteel = 0.2 MN/mm². The tensile force developed at a temperature of 50°C is ?