Q3: A steel pressure vessel shown in figure (2) below is sealed by a steel gasketed cap fastened with 8 preloaded bolts as shown in figure below. The cylinder stores gas at a maximum pressure Pg=1220 psi. The thickness of the gasketed cap is te =0.55 in, the diameter of the cylinder is de = 3.3 in, and the diameter of the bolt circle is dbc=5.8 in. Also, tp=0.55 in. It has been decided to use 7/16 -14 UNC 5/4 SAE Grade 8 hex-head bolts with washer. You may assume a non-permanent connection. Determine (a) the load factor nL, and (b) the joint separation factor no. (Elasticity modulus for steel, Estee=31 Mpsi). dhe - de Figure (2) 000

Q3: A steel pressure vessel shown in figure (2) below is sealed by a steel gasketed cap fastened with 8 preloaded bolts as shown in figure below. The cylinder stores gas at a maximum pressure Pg=1220 psi. The thickness of the gasketed cap is te =0.55 in, the diameter of the cylinder is de = 3.3 in, and the diameter of the bolt circle is dbc=5.8 in. Also, tp=0.55 in. It has been decided to use 7/16 -14 UNC 5/4 SAE Grade 8 hex-head bolts with washer. You may assume a non-permanent connection. Determine (a) the load factor nL, and (b) the joint separation factor no. (Elasticity modulus for steel, Estee=31 Mpsi). dhe - de Figure (2) 000

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter2: Axially Loaded Members

Section: Chapter Questions

Problem 2.2.9P: A safety valve on the top of a tank containing steam under pressure p has a discharge hole of...

See similar textbooks

Similar questions

Q3- A steel pressure vessel is sealed by a steel gasketed cap fastened with 8 preloaded bolts as shown in figure below. The cylinder stores gas at a maximum pressure Pg=1200 psi. The thickness of the gasketed cap is te =0.5 in, the diameter of the cylinder is d. = 3.25 in, and the diameter of the bolt circle is db=5.5 in. Also, tp-0.5 in. It has been decided to use 7/16 -14 UNC 5/4 (L=bolt length) SAE Grade 8 hex-head bolts with washer. You may assume a non-permanent connection. Determine the load factor nL, and the joint separation factor no. (Elasticity modulus for steel, Esteel=30 Mpsi) Note: P (load per bolt) = Pg AJN, where A, is the area of the cylinder. dpc
A steel cylinder head is connected to a grade 30 cast-iron pressure vessel using Nô bolts, as shown in Fig. 2. The cylinder stores gas at a maximum pressure pg = 3000 psi. The thickness of the cylinder head is te = 0.5 in, the diameter of the cylinder is de = 3.5 in, and the diameter of the bolt circle is dbc = 6 in. Also, tp = 1.5 in. It has been decided to use 3/8-16 UNC bolts without washers. You may assume a permanent connection. a Determine a suitable length for the bolt rounded up to the nearest ¼ in. Select the appropriate SAE bolt grade and determine the number of bolts required in order to satisfy the following requirements: The yielding factor of safety is at least 1.05. • The joint separation factor is at least 2.0. The maximum center-to-center distance between bolts is four bolt diameters. dpc de Figure 1
Problem 2 -41 In the figure shown, determine the difference in pressure between points A and B. Kerosene, s = 0.82 Air s = 0.0012 Benzene B° S = 0.88 100 mm +. 200 mm 150 mm 90 mm YMercury Water 400 mm
An air chamber is held together by bolts. d = 20 cm, D = 40 cm. A-A: 20 bolts, Dvolt = 2.5 cm. A B d- B Find: Number of bolts required at section B-B.
The figure illustrates the non-permanent connection of a steel cylinder head to a grade 30 cast- 8-35 iron pressure vessel us
QUESTION 1. A hydrazine tank, designed by Orbital Propulsion Center, is made of T16A14V STA (3.7164.7) titanium alloy is shown in the figure. a. The length of the tank is 890 mm and its volume is 176.5 liters. Calculate the radius of the tank. b. Determine the tank thickness, t such that the tank resists the proof pressure of 36.9 Bar without permanent deformation and the burst pressure of 49.2 Bar without fracture. c. Under the operational conditions (MEOP), determine the absolute maximum shear stress that occurs on the tank. http://www.space-propulsion.com/spacecraft-propulsion/hydrazine-tanks/index.html Surface Tension Propellant Tank OST 33/0 Net Volume Range 176.5 Litres Propellants Hydrazine (N,H) Spherical with a gylindrical Intersection Geometrical Shape Maximum Expected Operating Pressure (MEOP) 24.63 bar Proof Pressure (1.5 x MEOP) 36.95 bar Burst Pressure (2.0 x MEOP) 49.26 bar Interface Fixation 4 Suspension Trunnions Materials - Pressure Vessel TIGAIAV STA (3.7164.7) -…
A steel (E=210 GPa, v=0.32) cylindrical vessel has a diameter R= 25 cm, thickness t=0.2 cm and length L=100 cm. What is the increase in the length of this vessel if it is subject to PR PR. an internal pressure P kPa (unit in kPa)? (Remember: o, =
Figure illustrates the connection of a cylinder head to a pressure vessel using 10 bolts and a confined-gasket seal. The effective sealing diameter is 150 mm. D = 20 mm (E = 207 GPa), and F = 25 mm (E = 100 GPa). The cylinder is used to store gas at a static pressure of 6 MPa. Bolts with a diameter of 12 mm, a = 30°, pitch of 1.75 mm, nut thickness H = 14 mm, At = 84.3 mm?, W = 18 mm have been selected. (a) Find the bolt spring rate kp (use E = 207 GPa). (b) Find the upper, central and lower frustrum stiffness per bolt (c) Find the member spring rate km
A hemispherical window (or viewport) in adecompression chamber (see figure) is subjected toan internal air pressure of 85 psi. The window isattached to the wall of the chamber by 14 bolts.(a) Find the tensile force F in each bolt and the tensilestress s in the viewport if the radius of thehemisphere is 14 in. and its thickness is 1.25 in.(b) If the yield stress for each of the 14 bolts is50 ksi and the factor of safety is 3.0, find therequired bolt diameter.(c) If the stress in the viewport is limited to 500 psi,find the required radius of the hemisphere.
Task 2 In the shown Figure 2, a cylindrical pressure vessel of radius r = 36 cm and thickness t = 5 mm is subjected simultaneously to internal gas pressure of 1.2 MPa and a load P of 3 KN (Ignore the torque from load P). Let L = 0.7 m and find the x and y stresses at point a.
Repeat Problem 3.3-1, but now use a circular tube with outer diameter d0= 2.5 in. and inner diameter di= 1.5 in.
A circular shock absorber, as shown in the figure below, is designed to support a set of sensitive instruments. The system consists of an aluminium circular bar of diameter d1, a hollow circular rubber insulator acting as shock absorber of diameter d2 and height h, and an aluminium circular tube. The bar and the insulator are glued to each other. The rubber insulator is bonded to the aluminium circular tube. The aluminium circular tube is fixed on the ground. You are given the following inputs: F = 1000 N D1 = 4 mm D2 = 40 mm H = 40 mm G = 600 KPa T = 2 mm Select the best answers from those given below: Q1: Evaluate the maximum axial stress in the bar, bar,max= 79.6 MPa; Q2: Evaluate the maximum axial stress in the vertical section of the tube, tube,max 4.6 ✓ MPa; Q3: Evaluate the maximum shear stress occuring in the insulator, Tmax= 4.6 MPa; Q4: Assuming the bar and tube to be rigid, evaluate the maximum static vertical deflection of the bar, omax=15.3x10-6 mm F d₁ Side view t Saved…