Q3:A ring distributer (DC distributer) ABCDA is fed from point A with 250 v, and the resistance ofvaious sections are as follows:AB=0.02 2, BC=0.018 2, CD=0.025 2 and DA= 0.0202.The main supplies loads are 150 ampere at B, 300 ampere at C and 250 ampere at D.Determine the voltage at each load point.

Answered: Image /qna-images/answer/6431f015-354c-4c76-8660-7b52c9c8a0b4.jpg

Q3: A ring distributer (DC distributer) ABCDA is fed from point A with 250 v, and the resistance of vaious sections are as follows: AB=0.02 02, BC=0.018 , CD=0.025 02 and DA= 0.0202. The main supplies loads are 150 ampere at B, 300 ampere at C and 250 ampere at D. Determine the voltage at each load point.

Q3: A ring distributer (DC distributer) ABCDA is fed from point A with 250 v, and the resistance of vaious sections are as follows: AB=0.02 02, BC=0.018 , CD=0.025 02 and DA= 0.0202. The main supplies loads are 150 ampere at B, 300 ampere at C and 250 ampere at D. Determine the voltage at each load point.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

8) Three resistors of 10, 12 and X ohms, respectively are connected in parallel across a constant current source of 8A. Determine "X" if this resistor draws 2.13333333... A.
What is the magnitude of the resistance R in ohms in the circuit shown in the opposite figure?! A- 2 B-4 C-8 D-12 ..
Which of the following statements are correct for the circuit below? Thanks to the capacitors I – C1 and C2, the voltage gain of the circuit increases. II – Capacitors C1 and C2 are coupling capacitors and provide an isolation function between AC and DC voltages in the circuit. Thanks to the III – RE resistor, the voltage gain of the circuit increases. Thanks to the IV – RE resistor, the stability of the circuit increases. The V – C3 Capacitor is a bypass capacitor and prevents the loss of voltage gain. Capacitor VI – C3 is a coupling capacitor and has no effect on the voltage gain in the circuit. VII – As the value of the source internal resistance Rs increases, the voltage gain decreases. VIII – The voltage gain decreases as the value of any RL load to be added to the circuit increases
A ammeter has a resistance of 0.1 ohm and full range is 100 A. To incraese range to 1000 A find value of shunt resistance. Please solve it.
4. With reference to the Paschen curve below, Breakdown voltage (V) 60 55 50 45 40 35 30 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 pd (cm-torr) If a discharge at p = 0.1 torr, d = 20 cm is to be initiated, what is the voltage required to cause a breakdown? What will be the breakdown voltage if p = 0.025 torr, d= 20 cm?
Pt A 6v battey, delivrers loMA to thvee resistors in faralkl, R, =1kr,R2 =2K2,R3=Rx- Calcalate: a) Current in b) Power dissipatiod by Rx and R,-[Anss 6mw, 36mn. c) Resistance ratio Rx/R--(Ans: 6/)- d) Current ratio Ii/Ix. Anst 6/4). Rx stheatis Ix Anss 1 mÁ)
Q2) Consider the circuit in Figure (3), and answer 3 branch only. a) What type of circuit is this? b) What is the total peak secondary voltage? c) Find the peak voltage across each half of the secondary. d) Sketch the voltage waveform across RL. 4:1 120 V rms RL 1.0 k2 D2 eelee
Please answer it with further explanation. badly need it What are your observations in this table below. How this reverse bias condition and forward bias condition affects current and voltage. This data was simulated using multisim. You can notice the increasing value of battery voltage in 2nd column.
Q/ For the circuit in figure below find the Voltage across 30 ohm resistor (vo) .
PS1 (1) Determine the voltage and current meter indications in each circuit. R6 .3kOhm R5 .7kOhm T D7 IN4001GP Use Si diodes D3 XM15 D4 D2 X2014 X2017 R4 22.7kOhm R2 m 2.2kOhm D6 D5 X0013 X2016 XINIU VT -20 V R3 SkOhm R1 3kOhm x2011 X2018 2012 D1 X019 :: ...
Determine the voltage across R2 in the figure below, if the source is 6V, the Zener is 5.2V, R1= 10k ohms, and R2= 10k ohms.
1a. Calculate the equivalent resistance of R4 and R5 1b. Adding the values of resistor R1 and R2 to R equivalent. Calculate the circuit resistance seen by the power source. 2a. Measure the total resistance across terminals A and D, using ohmmeter function of the electronic VOM. Make sure that switch S1 is in the open position. Measured Total Resistance in Multisim= 4.15kohms 2b. Does the measured total resistance agree exactly with your calculated resistance? Explain