Q3 A partition is placed between two tank as shown in figure. Initially tank 1 contains 3.4 kg of water (liquid-vapor mixture) at 150°C with quality of 0.5. Tank 2 contain steam at: m-2.4 kg. P-1000 kPa, T= 300°C. The partition is now removed, and thermodynamic equilibrium is established. If the pressure at the final state is 300 kPa, find (a) temperature and quality of the steam at the final state and (b) the amount of heat lost from the tanks. Ta T-

Q3 A partition is placed between two tank as shown in figure. Initially tank 1 contains 3.4 kg of water (liquid-vapor mixture) at 150°C with quality of 0.5. Tank 2 contain steam at: m-2.4 kg. P-1000 kPa, T= 300°C. The partition is now removed, and thermodynamic equilibrium is established. If the pressure at the final state is 300 kPa, find (a) temperature and quality of the steam at the final state and (b) the amount of heat lost from the tanks. Ta T-

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

1.)What is the condition of the liquid at 212 F and 14.696 psia is : 2.) The vapor at 212 F and 14.696 psia ,in the absence of any liquid whatsoever ,what is its condition?
Q2: A 1-m³ tank contains 6.263 kg of steam at 0.6 MPa. Determine the temperature of the steam, using (a) the ideal gas equation, (b) the van der Waals equation Pc=3204 Psia Tc=1165.3 R°
Initially 3 kg of saturated water mixture at 300 kPa with a quality of 0.8 is contained in a piston-cylinder device. The water is heated at a constant pressure until the temperature reaches 500°C. Use the properties for water on the second the third pages of the equation sheet. a. Find the work done during the process. b. Find the change in internal energy of the water. c. Find the heat transfer during the process. Is heat added or removed from the system?
Required information On the property diagrams indicated below, sketch (not to scale), with respect to the saturated liquid and saturated vapor lines, and label the following processes and states for refrigerant-134a. Use arrows to indicate the direction of the process, and label the initial and final states. Use data from the steam tables. On the T-v diagram, sketch the constant-specific-volume process through the state T= 20°C, v= 0.02 m/kg from P = 1200 kPa to P2 = 300 kPa. For this data set, place the temperature values at states 1 and 2 on its axis. Place the value of the specific volume on its axis. Please upload your response/solution by using the controls provided below.
5 kg of air undergoes the cyclic process as shown in the figure. Determine the totalwork done in joules
3000 kJ of heat is given to 1 kg of water at 20 C. If steam with a pressure of 750 kPa is obtained as a result of this process, is this steam wet?institution? You should reach the result by typing the table values and operation steps. TIP: You should decide on enthalpy values using Thermodynamic Property Tables.
A 0.5-m3 rigid vessel initially contains saturated liquid–saturated vapor mixture of water at 120°C. The water is now heated until it reaches the critical state(point). Solve, 1. Show the process on T-v diagram with respect to saturation lines. 2. Determine the mass of the liquid water at the initial state.
Consider a balloon contains initially 40 liter of Helium at 105 kPa and 20 oC, The balloonis connected to a supply line of helium through a valve that is opened allowing helium tofurther fill the balloon to 150 kPa such that pressure in the balloon is expressed as: P =750 V0.5– 45, Where P is in kPa and V is m3. Considering Helium as ideal gas:a- Find the mass of Helium entered the balloon if the process is isothermal.b- Find the work done during the process.
An ideal gas follows the relationship pV=10 where V is in m3 and p is in kPaa. Draw the pV diagram and find the area under the curve (in kN-m) as the pressure decreases from 500 kPaa to 50 kPaa.
X=6
A piston-cylinder device contains an ideal gas of nitrogen. At the initial state, the volume is V1= 1.00 m3, the pressure is p1= 400.00 kPa, the temperature is T1= 300.00 K. An electric heater within the device is turned on for a time of Δt = 5.00 min. The current is I = 3.00 A, and the source voltage is V = 120.00 V. During the heating process, the gas expands, and a heat loss of Qout = 2.80 kJ occurs. The gas constant is R = 0.297 kPa·m3/(kg·K), and the room temperature specific heat at constant pressure is cp =1.039 kJ/(kg·K). Calculate the electrical work done on the gas, Wele__________ (kJ)