Q3/ A- Design the TDM system of the following 43 signals and calculate the transmitted bandwidth. 1- S1 band limited to 40kHz 2- S2 band limited to 20kHz 3- 18 signal (S3 to S20) each band limited to 5kHz 4- 14 signal (S21 to S34) each band limited to 312.5 Hz 5- 9 signal (S35 to S43) each band limited to 625 Hz f these analog signals converted to digital signals with signal to Noise ratio not less than 61.96 dB find the signaling rate in each join of the designed TDM system.

Q3/ A- Design the TDM system of the following 43 signals and calculate the transmitted bandwidth. 1- S1 band limited to 40kHz 2- S2 band limited to 20kHz 3- 18 signal (S3 to S20) each band limited to 5kHz 4- 14 signal (S21 to S34) each band limited to 312.5 Hz 5- 9 signal (S35 to S43) each band limited to 625 Hz f these analog signals converted to digital signals with signal to Noise ratio not less than 61.96 dB find the signaling rate in each join of the designed TDM system.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

please quickly thanks !
Given the AMI-RZ Line Coding Waveform, the corresponding binary data is _______
Find the output wavelength for the following serial in parallel out register attached below.
in AM signal with the following data : Vmax = 7.07V and Vmin = 2.998V. Calculate the modulation index (m) O a. m=1 O b. m=0.5 O c.m=0.204 O d. m=0.404
What is the maximum modulating frequency allowed in commercial FM broadcastings? a. 40 KHz b. 75 KHz c. 15 KHz d. 120 KHz
Answer questions 2.b.1) In 30 min
11:10 I ZYI N 1 a . "l zain IQ In DSB-SC-AM modulation the information carried by carrier is * zero more than information carried by USB less than information carried by LSB equal to information carried by any side A signal has a series of harmonics with frequencies (2 MHz, 6 MHz,10 MHz) and so on contain a third harmonic of 10 MHz 2 MHZ 6 MHz 3 MHz The benofit of I DE in AM DSR SCic *
What is the maximum modulating frequency allowed in commercial FM broadcastings? a. 40 KHz b. 75 KHz c. 15 KHz d. 120 KHz
The following are short samples of multichannel signal sampled at a rate of 10 Hz Ch1 -2 4 -6 -4 1 -2.5 4 5 7 Ch2 6 2 -2 7 1 3 Ch3 4 -1 5 3 9 -3 -3 8 2 Ch4 5 5 2 7 -1 Using window size of 500ms length and 40% increment of the window length, what is the value of the variance for the second window of the third channel? Your answer The noise voltage out of a 2 MN resistor is measured using a digital voltmeter as 2.5 uV at room temperature. What is the effective bandwidth of the voltmeter (Boltzmann's constant=1.38 x 10^-23 J/K) Your answer ++++
In case of 625-B television standard the maximum frequency deviation should not exceed ± 50 kHz. Calculate the FM channel bandwidth required for audio signal if the highest frequency content in the miedolating signal is 10 kHz and significant sideband frequency components equal to 7.
Question 1 In this problem, you are required to design a 30-channel FDM multiplex for the transmission of voice signals. There are two bands available with the following frequency ranges: Band 1: 50 kHz - 80 kHz Band 2: 200 kHz - 230 kHz It is also required to have a 2 kHz guard band (no guard band is required is the beginning, i.e., before the first user) between each adjacent signal to avoid signal interference (for band 1). For band 2, 3 kHz guard band is required between each adjacent signal to avoid signal interference (no guard band is required is the beginning, i.e., before the first user). Draw a clear block diagram of your 30-channel. The diagram must show the number of stages of the multiplexer, the starting and the terminal frequency of each stage, the frequency of each guard band in each band, and the frequency of each user in each band (refer to last slide of chapter 4c pdf file). You should also describe the details of your design to get full credit.
össlg äbäi Q) Which one of the following is a frequency sensitive ?bridge Maxwell bridge. O Wheatstone bridge. O Schering bridge O Wien's bridge. O