Q3/ A certain power supply generates a voltage v(t)=Vm cos(ot+ q) having a frequency of 13.56MHz. If the supply delivers a maximum power of 300 W to a 5 2 load and the voltage reachesa minimum at t= 21.15 ms, calculate Vm, 0, and o.Q4/ An alternating voltage is given by v(@t) = 75 sin(314t-0.25) volts. Find:(a) The rms voltage;(b) The average voltage;(c) The periodic time;(d) The instantaneous voltage when t= 4ms;(e) The time when the voltage is first a maximum.Q5/ Find the amplitudes and the phase relation for the following voltage waveforms:vi(t) = -50 cos(@t) – 30 sin(@t) Vv2(t) = 55 cos(mt) – 15 sin(@t) VSupport your answer with waveforms drawing.

As per the guidelines of bartleyby I need to answer first question only So kindly repost other…

Q3/ A certain power supply generates a voltage v(t)=Vm cos(@t+ P) having a frequency of 13.56 MHz. If the supply delivers a maximum power of 300 W to a 5 2 load and the voltage reaches a minimum at 21.15 ms, calculate Vm, 0, and p. 0LAn olternoting voltoge is givon by vleat) - 75 sin(314t 0 25) volts Find.

Q3/ A certain power supply generates a voltage v(t)=Vm cos(@t+ P) having a frequency of 13.56 MHz. If the supply delivers a maximum power of 300 W to a 5 2 load and the voltage reaches a minimum at 21.15 ms, calculate Vm, 0, and p. 0LAn olternoting voltoge is givon by vleat) - 75 sin(314t 0 25) volts Find.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A single phase ac voltage source has 200 V rms and a system connected consumes an active power of 300 W. What is the reactive power consumed by the system if 2.5 A rms current is drawn ?
A curve is drawm in descending order of load with time. Al1
6. Determine the rms current I as shown in figure 1. Source voltage is already in RMS value (Answer must be in polar form and should be in 4 decimal places). -j4 N j1.5 A B 4 0 A 200/30° V -j2 N: jIN Figure 1.
What is the common frequency of alternating current in the United States? Select one: A. 25 HERTZ B. 50 HERTZ C. 60 HERTZ D. NONE OF THE ABOVE
... 0.25 A 120 V 60 Hz RL 1 k2 470 µF When the circuit is working normally, it has an rms secondary voltage of 12.49 volts. Considering the ripple voltage, what is thnimum dc load voltage?
Determine the phase angle difference. Write the values only in degrees in four decimal places. the correct answer is 90 degrees. show the solution please. thank you
DRAW THE CIRCUIT AND KVL LOOPS ANALYSIS .
Describe the difference between AC (alternating current) and DC (direct current). Use illustrations.
In he giun airauit what resistor RL will absorb masimuon power and what is hir poscr! RL is cqual to (if your answrs are mot ahole numbers, round af to 2 deimal places.) ohms and Pmax is equal to wattr. 1SSL Tr2oN (0.2Vx
i need Full detailed Steps
A sinusoidal voltage with effective value (73 V), and a Frequency its value (80 Hz), was applied on a series circuit that consists of a coil with inductance of value (0.05 H), and a resistor of value (5 N). Calculate: 1. The maximum value of the voltage? 2. The inductive reactance of the coil? 3. The electric impedance of the circuit? 4. The maximum value of the generated current in the circuit? 5. The phase angle? 6. The power factor? 7. The power dissipated inside the coil? 8. Draw a diagram showing the results?
The graph below shows a voltage signal as a function of time. The dc voltage is 0. t1 = 39ms and t2 = 91ms. Determine the phase of the signal. Enter your answer in degrees rounded to one decimal place. If the answer is negative, be sure to include a minus sign.