Q2. Three 160 mm by 80 mm planks are glued together to form a wooden beam. This beam is simply supported at both ends as shown in figure below. Determine the maximum shear stress in a. The glue b. The wood 8 kN/m Glue 80 mm 80 mm - NA 6 m 80 mm 160 mm

Q2. Three 160 mm by 80 mm planks are glued together to form a wooden beam. This beam is simply supported at both ends as shown in figure below. Determine the maximum shear stress in a. The glue b. The wood 8 kN/m Glue 80 mm 80 mm - NA 6 m 80 mm 160 mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: A singly reinforced rectangular section has a width of 250mm and an effective depth of 460mm. The…

Q: (A)-Use the ultimate strength method to determine the design strength (Mu) for the beam shown in…

A: We know that design strength of doubly reinforced beam is given by Mu = ϕ.Mn =…

Q: 50 mm 50 mn 50 mm 50 mm 150'mm 50 mm 150 mm In the figure shown above the boards are glued together…

Q: The wooden members A and B are to be joined by plywood splice plates that will be fully glued on the…

A: Given data P = 35.9 KN Width (W) = 119 mm Length (L) = 288 mm x = 11m

Q: L25 KN 8 KN/m Dimension of rectangular section %3D 400 x 650 mm Initial Prestressing force = 380 kN…

A: Eccentricity (e) =150 mm Ytop=ybottom= 640/2 =320mm KNm= 1000000 Nmm Sign convention Compressive = +…

Q: Problem # 2: The composite bar is subjected to a normal force P = 7500 lb as shown in the figure.…

Q: The properties of the reinforced concrete beam are b = 303 mm, d = 466 mm, Ast = 1138 mm2, and Est /…

A: Bending Moment is 55.53 x 103Nm or 55.53 KN-M.

Q: The assembly is used to support a 10 kN point load at the tip as shown. The steel rod has a diameter…

Q: For the wooden beam sketched in the figure, ask for the mid-span section. a) Determine the normal…

A: To determine the normal stress at various points draw the normal stress distribution check for…

Q: - A joint is made by gluing two plywood gussets of thickness to wood boards. The tensile working…

A: The tensile working stresses for the plywood is 1200 psi.The tensile working stress for the wood…

Q: determine the largest bending moment (in Nm) that may be applied safely

Q: 1. In pre-stressed concrete application, the pre-stressing force is reduced with time because of: a.…

A: Solution: 1. In pre-stressed concrete application, the pre-stressing force is reduced with time…

Q: Two wooden members, each having a width of b = 3.9 in. and a depth of d = 1.3 in., are joined by a…

Q: 4 KN 2 KN 10 KN

A: Solution

Q: reinforced concrete beam

A: Given: The cross sections of the beam = 308 mm x 486 mm Width of the beam, b = 308 mm Depth of the…

Q: wood wood 250 mm

A: STRAIN IN STEEL= STRAIN IN WOOD εS=εWσSES=σWEWσS= Stress in steelσW= Stress in woodES=youngs modulus…

Q: Two wooden members, each having a width of b = 6.6 in. and a depth of d = 2.2 in., are joined by a…

A: Given:- b=6.6 ind=2.2 inβ=30o To find:- Value of force P

Q: A composite beam made of steel and bronze has the cross section shown. The cross-sectional…

A: To find the modular ratio for transforming steel to bronze n…

Q: 6. The beam shown in the figure carries DL= 10.5kN/m (including its own weight) and LL = 13.5kN/m.…

Q: shear stress, b) maximum bending stress, and c) maximum compressive stress. P Hinge L.

Q: A pretensioned member with a dimension of 250mm x 360mm is subject to an eccentric

Q: A cantilever wood beam with a span of L = 3.6 m supports a linearly distributed load with maximum…

Q: Three plates are welded together to form the section shown. Dimensions of the cross section are…

Q: A floor sheathing is supported by 75 mm x 250 mm wooden joists of unknown spacing. The joist has an…

A: GIVEN DATA:-⇒Length of joist (L)= 3.75m⇒Floor load (w) = 4.75 kpa⇒Allowable bending stress (σallow)=…

Q: mpressive stresses in the wood and steel if Ew = 11 GPa and E, MPa MPa

Q: A concrete column that is part of a truss is under stress. Determine the maximum tension strength of…

Q: Problem 2 A composite beam made of steel and concrete has the dimensions and layout shown below.…

Q: A beam, which is rectangular, has a base of 250 mm, and d = 625 mm. The beam is singly reinforced,…

Q: Two wooden members of (25 b) (60 b)-mm uniform rectangular cross section are joined by the simple…

A: Given:- The cross-section of the two wooden pieces = 25×b×60×b mm2 The load on the wooden piece (P)=…

Q: A composite beam is constructed using a steelplate (13 mm × 150 mm) with two wood beams (75 mm ×150…

A: Given data: Mz=6.75 kN.m

Q: The wood beam has a square cross section. Find the smallest allowable cross-sectional dimensions if…

Q: 4. The two pieces of wood, 2 in. by 4 in., are glued together along the 40⁰ joint as shown in figure…

A: Area of wood pieces, AngleTo find: (A) Maximum load for wood strength of . (B)…

Q: he T-beam has the following properties: flange thickness = 110 mm flange width = 700 mm web…

Q: : Calculate the bending stresses in concrete and steel if f, =345 MPa and the concrete strength fe =…

Q: SITUATION 1. A composite bar is made by attaching a copper rod of length 900 mm and diameter 30 mm…

Q: The rectangular wood panels is formed by joining two boards together using high strength adhesive in…

A: Maximum load will be minimum of three cases.

Q: mm web height = 350 mm

Q: o (MPa) B 100 95 compression 70 80 2 m 60 50 tension 40 32.2 20 C 0.75 m '0.75 m 0.5m E (mm/mm) 0.01…

Q: Problem 6: The wood beam is subjected to a load of 12 kN. Determine the transverse shear stress at…

Q: Determine the cracking moment

A: Cracking moment: - It is the limiting moment at which given section is safe if it exceeded causes…

Q: c) Find the stresses in the concrete and the reinforcement for the following applied moments: (i) -…

A: Modular ratio has to be determined.Lever arm has to be determined.Then the stress in concrete and…

Q: d. stress in the steel bars; e. deformation of the concrete post

A: Given Load Cross sectional area Modulus of Elasticity Required d. stress in the steel bars;e.…

Q: Determine the maximum concrete and steel stresses at the point of maximum positive and negative…

A: Fundamental part that is impacted by stresses in a construction would be the beam. Whenever loads…

Question

Q2. Three 160 mm by 80 mm planks are glued together to form a wooden beam. This beam
is simply supported at both ends as shown in figure below. Determine the maximum shear
stress in
a. The glue
b. The wood
8 kN/m
Glue
80 mm
B
80 mm
- NA
6 m
80 mm
160 mm

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Trending now

This is a popular solution!

Step by step

Solved in 4 steps with 6 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Two wood boards, each 18 mm thick, are joined by the glued finger joint shown. The finger joint will fail when the average shear stress in the glue reaches 1080 kPa. Determine the shortest allowable length d of the cuts if the joint is to withstand an axial load of P = 4.2 kN. Use a = 18 mm and b = 144 mm. d Glue b P P Answer: d = i mm
Mechanics of Deformable Bodies L T The wooden bar consists of two segments, each of length L. One segment has a square cross section of width d, the cross section of the other segment is a circle of diameter d. The working stress for the wood is tw=5MPaand the shear modulus isG=0.5GPa. Using L=0.6m and d=50mm, determine (a) the largest torque T that can be safely applied; and (b)the corresponding angle of twist for the bar.
Show complete solution pls X=646 Y=46 A=8 B=7 C=8
T beams
Prob.5: A rectangular reinforced concrete beam has dimensions b = 300 mm, d = 530 mm and h = 600 mm, and is reinforced with 3 Ø32 mm bars. Materials strength are fe = 28 MPa, fy= 414 MPa. a) Find the moment that will produce the first cracking at the bottom surface of the beam basing your calculations on Ig. b) Determine the maximum stress in the steel and in the concrete under this Design of Reinforced Concrete Structures moment.
ASAP!!! NEED RIGHT COMPLETE SOLUTION !!!
Concrete has no tensile strength. True False
Use the giuven values: Aluminum: E = 10 x 106 psi, α = 12.8 × 10-6 in/(in·°F) Bronze: E = 12 x 106 psi, α = 10.5 × 10-6 in/(in·°F) Show you complete solution.
A rectangular beam has a width of 280 mm and an effective depth of 500 mm. It is reinforced with 4-36 mm diameter bars at the tension side of the beam placed 75 mm above the bottom of the beam. f = 25 MPa, fy = 414 MPa, E, = 200,000 MPa. Which of the following is the nominal moment capacity of the beam.
Show complete solution pls X=646 Y=46 A=8 B=7 C=8
i need the answer quickly
1. Figure shows two wood members are joined together using a 60 degrees wood glue adhesive. Find the average normal and shear stress resisted in the plane of the connection. 25 mm 8 kN- 8 kN 60° 30 mm