Q2. The given bridge truss supports point loads of 200kN at joints B, D, F, H, and J. The structure is supported by pin support at the joint A and roller support at the joint I. Determine the member forces AD, CE, CF, FH, Gİ, and IJ. Indicate whether the forces are compression or tension. Show your calculation steps in detail and write your answers in the box below. 200 kN 200 kN 200 kN 200 kN 200 kN D F B 7 m 3 m 4 m -5 m 5 m -5 m- -5 m-

Q2. The given bridge truss supports point loads of 200kN at joints B, D, F, H, and J. The structure is supported by pin support at the joint A and roller support at the joint I. Determine the member forces AD, CE, CF, FH, Gİ, and IJ. Indicate whether the forces are compression or tension. Show your calculation steps in detail and write your answers in the box below. 200 kN 200 kN 200 kN 200 kN 200 kN D F B 7 m 3 m 4 m -5 m 5 m -5 m- -5 m-

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A load of P = 50 kN acting at an angle of ß = 32° is supported by the structure shown. The overall dimensions of the structure are a = 2 2.9 m, b = 0.3 m, c = 1.0 m, e = 0.31 m, and x₁ = 2.0 m. The cross- sectional dimensions of member BC are bf = 170 mm, tf = 13 mm, d = 330 mm, tw = 11 mm, and h = 110 mm. Determine the principal stresses and the maximum shear stress acting at point H in member BC. Show these stresses on an appropriate sketch. E 45° XI (1) B e H a X d H X
Problem 6.42 Consider the truss (Figure 1). Suppose that F = 14.5 kN Figure 1 4 kN of 1 6 kN H B m G 2 m 9 KN C -1.5 m 1.5 m 1.5 m 1.5 m 1 m D > 6 kN E Part A Determine the force in member BC. State if this member is in tension or compression. Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive value in the case of tension. FBC = Submit Part B FHC = D μA Submit Value My Answers Give Up Determine the force in member HC. State if this member is in tension or compression. Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive value in the case of tension. Units μA Value Units ? My Answers Give Up ? Part C Determine the force in member HG. State if this member is in tension or compression. Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of…
Suppose that P= 1500 lb. Determine the force in each member of the cantilevered truss. Express your answer in kilopounds to three significant figures. Enter negative value in the case of compression and positive value in the case of tension. a) FDE b) FDF c) FGF
Using the method of joints, determine the force in all truss bars. Indicate tension or compression.
Determine the largest weight W that can be supported by the two wires AB and AC as shown in Figure below. The working stresses are 100 MPa for AB and 150 MPa for AC. The cross-sectional areas of AB and AC are 400 mm² and 200 mm2. B 45° 30° W O 44,524.65 KN 51,328.96 KN 37, 42.67 KN 41,213.20 KN
Truss Analysis (Method of Joints) What is the value of force in member AB? AC? BC? BD? CD? CE?
The structural frame below is loaded as shown. Determine the required area for members AB, ED,CD, AF, and FG considering the material’sproperty below : E= 200GPa, Allowable Stress for Compression is 120MPa and 315MPa for tension. Note : all units in meters.
2. Determine the resultant of the forces applied on a simply supported beam as shown. SKU SKN म im+im+im+ 2m HOKNI
A simply supported girder spans 10 m. It carries two beams each at 3.5 m from the supports. The concentrated load from each beam is 70 kN
Q2. The given bridge truss supports point loads of 200KN at joints B, D, F, H, and J. The structure is supported by pin support at the joint A and roller support at the joint I. Determine the member forces AD, CE, CF, FH, GI, and IJ. Indicate whether the forces are compression or tension. Show your calculation steps in detail and write your answers in the box below. 200 kN 200 kN 200 kN 200 kN 200 kN D F В H E m 4 m 3 m A 5 m -5 m -5 m 5 m
B1
ENGINEERING MECHANICS RATE WILL BE GIVEN! NO LONG EXPLANATION NEEDED! SHOW THE COMPLETE SOLUTIONS. ANSWER IN 4 DECIMAL PLACES.