Q2. (30%) Write a commented 8085 assembly language program to replace the already stored 05 hexadecimal numbers starting from the memory location 6000H with the already stored other 05 hexadecimal numbers starting from the location 6100H. Moreover, while exchanging the given two data sets, find the greatest number among the data sets and display it at one of the putput ports. The two data sets of hexadecimal numbers are given as: Data set starting from the location 6000: 23, 24, 45, 46, 48 Data set starting from the location 6100: 14, 35, 36, 40, 42

Q2. (30%) Write a commented 8085 assembly language program to replace the already stored 05 hexadecimal numbers starting from the memory location 6000H with the already stored other 05 hexadecimal numbers starting from the location 6100H. Moreover, while exchanging the given two data sets, find the greatest number among the data sets and display it at one of the putput ports. The two data sets of hexadecimal numbers are given as: Data set starting from the location 6000: 23, 24, 45, 46, 48 Data set starting from the location 6100: 14, 35, 36, 40, 42

Database System Concepts

7th Edition

ISBN:9780078022159

Author:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Publisher:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Chapter1: Introduction

Section: Chapter Questions

Problem 1PE

See similar textbooks

Similar questions

Please ONLY ASSEMBLY CODE ! NOT C CODE !
Q1- Write a program in assembly language for the 8085 microprocessor to send one byte of data located at the memory address (3000H ) using SOD at a baud rate of 1200. Information: The 8085 processor operates at a frequency of 3.072 MHz . When sending the required byte, you must adhere to the following: The two high bits of the start bits(1 1) must be sent, after that the data bits are sent, after that the low bit of the stop bit (0) is sent. The following flowchart will help you. The solution must be integrated and include the calculation of the baudrate delay time
Q1- Write a program in assembly language for the 8085 microprocessor to receive 10 bytes of data via the SID and store it at the memory address (3000H to 3009H) using a baud rate of 1200. Information: The 8085 processor operates at a frequency of 3.072 MHz. When you receive each byte of the required bytes, you must adhere to the following: The bits of two high bits will be received at the beginning of the reception (start bits), after that the data bits will be received, after that the low bit of the stop bit will be received (stop bit). The following flowchart will help you, but you should notice that this flowchart deals with one byte, and you are required to deal with 10 bytes The solution must be integrated and include the calculation of the baudrate delay time Of+CD!HID+[00 Yes SIDATA Read SID Start Bit? Wait for Half-Bit Time Set up Bit Counter Wait Bit Time Read SID Save Bit Decrement Bit Counter All Bits Received? Add Bit to Previous Bits Go Back to Get Next Bit Return IMUNI
Transcribed Image Text (Micro processer 8086) Q1) Choose the correct answer: 1. One of the following instructions is correct: a. MUL 67 b. LEA BL.[SI] (2. AS) c. LALF d. Neither a,b nor c 2. Suppose we have SS starts at B4102 H, CS ends at E4250H. The suitable point for DS to start so there are no overlapping of the segments is: c. C4200 H d. C4300 H a. C4000 H b. C4100 H 3. If you have AX-0208H, BL=D8H, the results of performing IDIV BL in AX is: a. 00F3 H b. F300 H c. 5802 H d. 0258 H 4. The Execution Unit includes: a. Instruction pointer b. Status register c. Address generation d. Neither a,b nor c 5. The compare instruction and test instruction are similar in : a. Both instructions are subtraction methods b. Both instructions effect on ZF, SF & PF. c. Both instructions store the result in the destination operand d. Neithe a,b nor c 6. The data bus in 8088 Mp is: a. 16-bit unidirectional lines c. 8-bit unidirectional lines b. 16-bit bidirectional lines d. 8-bit bidirectional…
Microprocessor and Microcontrollers. Kindly give full write up solution of this question.
Fill all the information to reflect the addresses of the program memory Adress code, .org 0x540 LDS R10, 0x700 LDI R20, 20 LDI R16, 10 ADD R16, R20 STS 0x700, R16 ADD R16, R10 STS 0x701, R16 Ox540 Ox541 Ox542 Ox543 Ox544| Ox545 0x546|| Ox547 Ox548 0x549 0x54A
Q2- Write a program in assembly language for the 8085 microprocessor to receive one byte of data via the SID and store it at the memory address (3000H to 3009H) using a baud rate of 1200. Information: The 8085 processor operates at a frequency of 3.072 MHz . When receive the required bytes, you must adhere to the following: The bits of two high bits will be received at the beginning of the reception(start bits 1 1 ), after that the data bits will be received, after that the low bit of the stop bit will be received (stop bit 0 ). The following flowchart will help you. The solution must be integrated and include the calculation of the baudrate delay time
25: . Find the time delay in the following program if the crystal frequency is 1 MHz. Do not ignore the time delay due to the first and last instruction. DELAY: LDI R16, 30 AGAIN: LDI R17, 35 HERE: NOP NOP DEC R17 BRNE HERE DEC R16 BRNE AGAIN RET 26: Write a program to display 2 on 7 segment. A 7 segment is connected to PortD.
2. What is the value of the doubleword stored in memory starting at address B000316 contents of memory locations B000316 , BO00416 , BO005,6 , and B000616 are 1116, 2216, 3316 , and 4416 respectively? Is this an example of an aligned double word or a misaligned double word? if the
DO NOT COPY OTHER ANSWER
2.
write the following questions a) Write an 8051 C program to send Hex values for ASCII characters of 0,1,2,3,4,5AB,C and D to port P1 b) Interface a 4X4 keyboard with 8086 using 8255, and write an ALP for detecting a key closure and return the key code in AL. The debouncing period for a key in 20 ms