Q2- Water density =1000 kg/m³ and viscosity is 0.001 N s / m², is pumped between two reservoirs at 0.2m³/s through a 400 m of 8 cm diameter Cast Iron pipe and several minor losses as shown in the figure. Compute the pump power required in kW. Use the last one digit of your ID number for Zį level in meter.

Q2- Water density =1000 kg/m³ and viscosity is 0.001 N s / m², is pumped between two reservoirs at 0.2m³/s through a 400 m of 8 cm diameter Cast Iron pipe and several minor losses as shown in the figure. Compute the pump power required in kW. Use the last one digit of your ID number for Zį level in meter.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Use g=32.2 */sec2 (9.81 m/s2) and 60°F (16°C) water unless told to do otherwise.• Google schedule-40 pipe’s thickness at different nominal size to obtain the innerdiameter of the pipe for accurate determinaLon of flow velocity.• Must show your work to support your selecLon. Otherwise, no points will be given.Water flows through a schedule-40 pipe that changes gradually in diameter from 6 in (154mm) at point A to 18 in (429 mm) at point B. The volumetric flow rate is 5.0 *3/sec (130 L/s). The respecLve pressures at points A and B are 10 psia (70 kPa) and 7 psia (48.3 kPa). All lossesare insignificant. What are the direcLon of flow and velocity at point A? (A) 3.2 */sec (1 m/s); from A to B(B) 25 */sec (7.0 m/s); from A to B(C) 3.2 */sec (1 m/s); from B to A(D) 25 */sec (7.5 m/s); from A to B
Find the difference in pressure head and velocity of flow of an oil through a pipe, when the difference of mercury level in a different U-tube manometer connected to the two tappings of the pitot tube as 108 mm. Take co-efficient of the pitot tube ("L" shaped measuring instrument) as 0.9 and sp. gr of oil = 0.8 Difference in pressure head (unit in mm) = Velocity of flow (unit in km/hr) =
Water is stored in a tank sketched in the figure below to support the demand of a nearby community area.The system is designed so that pressure at the location B always lies in the range of 330 to 440 kPa (gauge).Water demand fluctuates between 0.3 and 1 m3/s regardless of pressure at B. The supply pipe of 600 mmdiameter and 1 km length between A and B is made of steel and has the equivalent sand roughness of 1 mm.Although not shown in the figure, the supply pipe has five 90◦ bends, each having the head loss coefficientof 0.8. The figure shows that the bottom end of the tank is located 42 m above the ground, and the pipe isburied 1.5 m below the ground. A pump system regulates so that the tank keeps the same water level all thetime. Assume water at 20◦C, and air in the storage tank has the atmospheric pressure. To meet the designcriterion for pressure at B, what should be the depth of water h in the storage tank?
1. A pressure gauge attached to a pipe is reading 1.34 m of Hg at a place where the atmospheric pressure is 10.33 m of water. The approximate absolute pressure at the mountain isa. 930 kPab. 181 kPac. 280 kPad. 100 kPa 2. The flow is said to be unsteady and non-uniform when,a. The flow velocity is not changing with time but changing with spaceb. The flow velocity is changing with both time and spacec. The flow velocity is changing with time but not changing with spaced. The flow velocity is not changing with both time and space 3. The below figure shows a pipe with a circular cross section of diameter D mm on the left end and a square cross section with side D mm on the right end. Mercury enters the left end with a velocity 1 cm/s and leaves the right end with a velocity V2. Find V2 (neglect losses in the pipe).a. Cannot be find since length is not givenb. Cannot be find since diameter is not givenc. 7.85 mm/sd. 12.73 mm/s 4. 1 kg water is flowing through an inclined pipe at…
1.28. The performance curve for the fan of Problem 1.27 can be approx- imated by a straight line through its BEP (using techniques devel- oped in Chapter 7). The curve is Aps = 4488 – 166Q, with ApT in Pa and Q in m³/s. If this fan is connected to a 1-m dia- meter duct (f = 0.045) whose length is 66 m, what flow rate will result? %3D
Between two sections in a vessel, a fluid moves in a steady flow manner. At entrance: A1=20 m2, ρ1=1300 kgm/m3. At exit: A2=10 m2, ʋ2=0.00125 m3/kg, ῡ2=3 m/min. Determine the following: a) ḿ1 in kg/min b) ῡ1 in m/min
A 100 kW pump is moving water at 1 m^3/min. If the inlet pressure is 200 kPa (gauge), what is the outlet pressure
Flow Through Pipes A pipe 800 m long connects two reservoirs whose level difference is 60 m. Find the discharge in pipe in Liters/sec, if diameter of pipe is 0.5 m Take all losses into account. Assume f = 0.01.
1-A steel discharge pipe with a roughness equal to 0.5 mm is 800 m long and pumps 265 m³ of water per hour at a temperature of 20°C. The pipe diameter is 25 cm. Calculate the head loss. Data: kinematic water viscosity equal to 10-6 NOTE: if necessary, use Moody's DiagramHelp?