Q2:EMFField current (A) 2When run as a shunt generator at 400 r.p.m , Find :The O.C.C. of a d.c. generator driven at 800 revnin is as follows :(V) 220 310 372 | 424 | 460144925206 7| 8542| 391. Voltage to which the machine will excite with shunt field resistance equal to 350.2. lowest possible speed at which an O.C. voltage of 220 V can be obtained.

Answered: Image /qna-images/answer/ca7b713c-a520-409c-847d-3bff516c6e06.jpg

Q2: The O.C.C. of a d.c. generator driven at 800 revmin is as follows : |EMF Field current (A) 2 When run as a shunt generator at 400 r.p.m, 1. Voltage to which the machine will excite with shunt field resistance equal to 350. 2. lowest possible speed at which an 0.C. voltage of 220 V can be obtained. (V) 220 310 372 | 424 | 460 6 7 Find : 492 520 542 |3 4 | 8 9

Q2: The O.C.C. of a d.c. generator driven at 800 revmin is as follows : |EMF Field current (A) 2 When run as a shunt generator at 400 r.p.m, 1. Voltage to which the machine will excite with shunt field resistance equal to 350. 2. lowest possible speed at which an 0.C. voltage of 220 V can be obtained. (V) 220 310 372 | 424 | 460 6 7 Find : 492 520 542 |3 4 | 8 9

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Dc Generators Examples 7) The flux per pole of a four-pole generator is 0.05 wb. It driven at a speed of 1500 rpm. In order to have an induced emf of 20 v per conductor, if the winding is lap-connected, find (a) the number of conductors in series in each parallel path, (b) the number of conductors between brushes to generate 240 v, and (c) the total number of conductors in the armature. II 9) A short compound dc generator supplies a current of 100 A at a voltage
A 2 pole wave wound dc shunt generator runs at a speed of 750 rpm, has an armature and shunt field resistance of 0.4 and 580 respectively. The armature has 960 conductors and flux per pole is 0.115 Weber. If the lamp load connected has a resistance of 70 determine (i) Generated EMF, (ii) Total Resistance, (iii) Armature Current, (iv) Terminal Voltage.
Q2-A 4- pole lap-wound, 900 r.p.m shunt generator has armature and field resistances of 0.442 and 1752 respectively. The armature has 440 conductors and the flux per pole is 0.07 Wb. if the load resistance is 102 .Calculate the terminal voltage and load current delivered by the generato
The series field winding of a 170 kW, 250 V, 1450 rpm compound generator has a resistance of 0.00306 ohm. What will be the required resistance (in Ohm) of a noninductive diverter that will bypass 27 percent of the total armature current? "
The armature winding resistance of a long shunt connected DC generator is 0.4ohm, the resistances of the shunt and serial field windings are 125 ohms and 0.1 ohms, respectively. While the generator supplies 8KW of power to the load it feeds, which is the voltage it produces since the output voltage is 250V?
Q8) A two-pole de generator has an armature containing a total of 40 conductors connected in two parallel paths. The flux per pole is 0.02 web, and the speed of the prime mover is 30 rpm. The resistance of each conductor is 0.01 ohm, and the current-carrying capacity of each conductor is 10 A. Calculate: (a) The average generated voltage per path and the generated armature voltage (b) The armature current delivered to an external load (c) The armature resistance (d) The terminal voltage of the generator.
A 20-kW 220-volt shunt generator has an armature resistance of 0.07 ohm and a shunt resistance of 200 ohms.Determine the shunt field current A. 0.1 A B. 1.1 A C 2.1 A D. None of these
Two de generators each having linear characteristics that operate in parallel. One machine has a terminal voltage of 480V at no load and 220 V at a load current of 100A, while the other machine has a voltage of 470 V at no load and 200 V at 120 A. calculate the current in each generator and the bus bar voltage when the total load is 180 A. What is the kilowatt output of each machine under this condition?
COntact drop. ing at 500 rev/min, is given below: 2 4 Field current (A) Generated e.m.f. (V) 6. 135 179 202 214 10 71 The generator is now shunt-connected and run at 600 rev/min, the resistancc of the field circuit being 25 2. What e.m.f. will it generate? If the generator is placed on load and the terminal p.d. becomes 230 V, what is the load current? The armature resistance is 0-2 2 and armature reaction is to be neglected. (App. El., L.U.)
A short-shunt generator supplies 220A at 260V. The armature resistance is 0.15Ω, shunt field resistance is 50Ω, and the series field resistance is 0.2Ω. If the SPL amounts to 4% of the total power output, determine the efficiency (in %).
Choose True (V) or false( x) for the following : 4) Reluctance is a measure of "opposition" the magnetic circuit offers to the flux. 5) The rated output power (transformer rating) can be used to determine the turns ratio of the transformer. 6) With the increase in speed of a series DC motor, Both back emf as well as line current increase. 7) When an induction motor is stationary, the stator and rotor windings form the equivalent of a transformer. 8) Increasing the load current for DC Self-excited generator Shunt-Wound Generator will increase the terminal voltage. 9) In lap windings there are as many paths in parallel and used to produce high current, low voltage output. 10) In 3-pahse induction motor, if the rotor speed increases, the rate at which the rotating magnetic field cuts the rotor bars is increasing.
➡ A four-pole Series connected generator has a lap connected armature with 728 conductors. If the generator supplies one hundred incandescence lamp (100 V, 60W). The series field and armature resistance are 0.2 ohms and 0.015 ohms respectively. Find the series field current.