Q2): The N-bit DAC with an (R-2R) ladder network is to be designed as a 6-bit DAC device. Let (VREF= -5 V and R=R;=5 k2). (a) What are currents (I1, I2, 13, l4, I5, and I6)? (b)The input changes by 1 LSB. What is the change in the output voltage? (c) What is the output voltage if the input is (010011)? (d)What is the change in output voltage if the input changes from (101010 to 010101)?

Q2): The N-bit DAC with an (R-2R) ladder network is to be designed as a 6-bit DAC device. Let (VREF= -5 V and R=R;=5 k2). (a) What are currents (I1, I2, 13, l4, I5, and I6)? (b)The input changes by 1 LSB. What is the change in the output voltage? (c) What is the output voltage if the input is (010011)? (d)What is the change in output voltage if the input changes from (101010 to 010101)?

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Why is the R-2R ladder DAC design better than a binary-weighted DAC design, particularly if you extend to 16 bits?
Create Op-amp circuit... with:Vin= -1 Volt (DC) Vout = 14 Volt (DC) Only resistors with 1k, 3k, 5k, 7k and 11k ohms can be used while the circuit is being built. The V+ value of the LM741 IC to be used for op-amps will be 20 volts and the V- value will be -20 volts. You need to use at least one inverting amplifier and one non-inverting amplifier to build the circuit. Question: Write the gain formula of the circuit and calculate it, and write how we should find the Vout value..
Dynamic Circuit Design: a. Draw a 4-input Domino AND circuit and briefly explain how it works. b. Write at least 2 disadvantage of dynamic circuit design methodology.
Please do it in handwritten, thank you!
Input signals are given as V1= 3sin(wt), V2= 2sin(wt) and V3= 1sin(wt) in circuit.) a) Find equation that expresses output signal in terms of input signals. b) Write sinuzoidal expression of output signal.
3 A. We have a 4-bit DAC with Vref = 3.3V and an input voltage of Vs = 2.05V. Draw a diagram illustrating the conversion process of a successive approximation ADC. Label the x-axis conversion step and the y-axis Digital Number(DN). What digital number (DN) will be returned by the DAC within the SAR ADC? 3 B. You have purchased an 8-bit R-2R digital to analog converter to control the joint position on a robot arm (which is proportional to the input voltage). a). The DAC shows an output voltage of 0.49 V when the binary value 00011001 is applied. What is the full-scale analog output range of this DAC in volts? b). What voltage does the DAC output with a binary value of 10101010 applied? c). If the joint rotates 10.0 degrees/V applied, what is the minimum joint rotation increment you can achieve with this DAC?
Plz I need the answer of this question in digital system design
In Basic electronics lab on summing amplifier Arifa is asked to give the circuit connectionaccording to figure below to make a three input summing amplifier. She uses IC 741 as OP-AMPand two power supplies to power up the IC. According to the instruction of his teacher she usesthree input such that ?1 = 2?, ?3 = −1? & set ?2 such that the output voltage ?0 = −16.5?. A. What is the virtual ground of OP-AMP?B. Draw the equivalent circuit of OP-AMP and then simplify it for Ideal case.C. Determine the value of ?2 from the figure above for which ?0 = −16.5?.D. If the 50KΩ feedback resistor is replaced by a capacitor of 100uF what will be the outputvoltage after 1 second. Use the value of ?2 = 5 ???(200??)?�
Input signals are given as V1 = 3sin(wt), V2 = 2sin(wt) ve V3 = 1sin(wt) in circuit. a) Find equation that expresses output signal in terms of input signals. b) Write sinuzoidal expression of output signal
Can you answer question a), b) and c)?
please show the step claerly
Sketch the output voltage waveform for each op armp circuits given below. Given the maximum outputvoltage for the op-armp is Vomax = +10 v and Vomin = -10 v.Use input voltage for all circuit as shown. Also use V2 = 4.7 V for D1 and D2. V. 0 -5V- -5V D1 Kt 1K 1K D2 V1 V2