Q2 The forces are applied at the tip A of the vertical column as shown in Figure Q2. Determine: (i) The sketch of free-body diagram showing force components, (ii) The forces F1 and F2 in a cartesian form, (iii) The resultant force of Ft and F2 in a cartesian form, (iv) The magnitude of the resultant force, and (v) The angles of the resultant force. F; = 125 N 20 60° 45° 60 F = 400 N Figure Q2

Q2 The forces are applied at the tip A of the vertical column as shown in Figure Q2. Determine: (i) The sketch of free-body diagram showing force components, (ii) The forces F1 and F2 in a cartesian form, (iii) The resultant force of Ft and F2 in a cartesian form, (iv) The magnitude of the resultant force, and (v) The angles of the resultant force. F; = 125 N 20 60° 45° 60 F = 400 N Figure Q2

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: 4-5. The tip of a one-link robot is represented as a → position vector P as shown in Fig. P4.5. Find…

Q: F3 = 750 N 45°- 5 30° F, = 850 N F2 = 625 N

Q: 1. From figure 1.1. Determine the distance 'a' as a fraction of the beam's length 'L' for locating…

A: Take moment about A∑ MA=0 3PL-RCL-a+PL6=0RC=196PLL-a∑ Fy=0 RA+RC=4PRA=4P-196PLL-a

Q: |20 lb 12 |A I in. 80 lb 3 B

Q: Determine the vertical displacement of joint C of the truss shown below using Castigliano's theorem.…

A: A truss is given with pin support at A and E.The truss also supports two point loads 24kN and 40kN…

Q: 68 lb/ft 34 lb/ft 34 lb/ft 548 ft Ib B 2.8 ft 2.8 ft

Q: The force shown acts on the hook. Express it as a Cartesian vector.

A: As shown in figure (b), the coordinates for points A and B are A(2 m, 0 m, 2 m) and…

Q: The force system shown in the Figure MTE-2 consists of the couple C and the four forces. The…

A: Given: The resultant force is 75 N. The angle is 50o. Consider the figure,

Q: F₂ = 50 lb

Q: The beam of negligible weight is supported by springs at point A and B. Spring A has a spring…

A: Given data - d1 = 2 m d2 = 2.5 m W = 600 N/m K1 = 800 N/m K2 = 1550 N/m Find out - a. Determine the…

Q: Q.3) The structure below is subjected to a set of forces as shown. a. Replace the given system by an…

Q: The three forces act on the pipe assembly. If F1 = 80N and F2= 50 N replace this force system by an…

Q: oblem 2: uts: ● ● ● a = 0.35 m b = 1.2 m F₁ = 27 N F₂ = 35 N F3 = 68 N ing the scalar approach,…

A: a=0.35m b=1.2m F1=27N To find moment produced by all force about axis AB

Q: Learning Goal: To use the superposition principle to find the state of stress on a beam under…

Q: Problem 3.2 - Determine the moment about corner A due to the given 4-lb force a) by using the direct…

A: Moment about corner A

Concept explainers

Bars

In civil engineering, bars refer to steel reinforcement bars or rebars. These are structural members primarily used for reinforcement purposes in masonry works. A bar is characterized by its cross-sectional area, which is negligible compared to its length. Bars are usually manufactured by steel which is uniform throughout the length, or by meshing multiple steel wires. Other materials of the bar include carbon steel, glass fiber, carbon fiber, and basalt fiber. The reinforcing bars are coated with epoxy resins and other materials to enhance some of their properties including corrosion resistance.

Question

Q2 The forces are applied at the tip A of the vertical column as shown in Figure Q2. Determine:
(6) The sketch of free-body diagram showing force components,
(ii) The forces F1 and F2 in a cartesian form,
(iii) The resultant force of Fi and F2 in a cartesian form,
(iv) The magnitude of the resultant force, and
(v) The angles of the resultant force.
F; = 125 N
20
60°
45°
60
F = 400 N
Figure Q2

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Solve the given problem
Hope you are familiar with this kind of problem. Please draw the complete free body diagram including all the components.
The bar ABC has multiple bends in different directions. It has a force applied at point C. Using the listed parameters, find the resulting moment about A expressed as a Cartesian vector. A LA B. X y C 02 F value units L1 parameter 275 mm L2 L3 L4 400 mm 225 mm 475 mm 70 80 F 60 The moment about point A = }N-m NOTE: Use i, j, k for i, j, k
Can I get a detailed solution using the force method of analysis please????
The pressure loading on the plate varies uniformly along each of its edges. Determine the magnitude of the resultant force and the coordinates (x̄, y̅) of the point where the line of action of the force intersects the plate. Hint:The equation defining the boundary of the load has the form p = ax + by + c, where the constants a, b, and c have to be determined.
need help on this part
Pls answer a to d.
Read the question carefully and give me right solution according to the question. If you don't know the solution please leave it.
A force F= 338 N is applied as shown to the bracket ABC. a=134 mm; b=54 mm; c=90 mm; B=33 in degree. F a IB b 4a) Determine the y component of the moment of the force F about point A in Nm.
F1 F2 b M a C A a a Given the system above, F1 = 34 N, F2 = 96 N, M = 245 N-m, a = 3 m, b = 2 m, and a = 40°. %3D (a) Represent the system using a single force. Determine the magnitude of the force and its location relative to point A. Round all answers to the nearest integer. The magnitude of the force (N) is: N The position of the force relative to A (m) is: m (b) Represent the system using a force and a couple moment acting at point C. Determine the magnitudes of the force and the couple moment. Round all answers to the nearest integer. The magnitude of the force (N) is: N The magnitude of the couple moment (N-m) is: N-m
If the vertical component of the force F applied to the ring is 10 lb, determine the magnitude F and also the horizontal component. F 300
The force F has a magnitude of 610 lb and acts along the line AM where M is the midpoint of the vertical side OB of the parallelepiped. Express F as its magnitude times the appropriate unit vector and then determine its x-, y-, and z-scalar components.