Q2\ The following readings were recorded for voltage measurement 5, 4,6.8 , 4,5, 6.8,7.4, 6.8, 7.4,4,6.8, 5, 7.4 Calculate: Arithmetic mean (x), deviation from the mean (d) , variance (v) average deviation (D) Standard deviation (6), probable error ( r)

Q: Q1/a: theirs clear deferent between linear reference and sawtooth more harmonics less harmonics…

A: 1) a :  Sawtooth waveform is not symmetrical about real axis so it contains all harmonics. i.e it…

Q: In induction type energy meter, Recording system consists of a set of dials…

A: Induction type energy meter

Q: Two shunt generators operate in parallel to supply a total load current of 3,000 A. Each machine has…

A: In this question we need to find the load voltage and the armature current of each machine.

Q: List two examples and explain the reasons regarding to the behavior of power electronics device…

A: Based on their ON and OFF condition of the Power Electronics devices it can be categorizes in three…

Q: Discuss whether NEC provides the maximum requirements or minimum requirements.

A: NEC is the acronym of National Electrical Code.

Q: Describe the construction and operation of a TRIAC and give one practical application of the device.…

A: TRIAC: A TRIAC is a three-terminal electrical component which may conduct current in any direction.…

Q: I need a complete experience about Dispersion Compensation technique for the optical  fiber…

A: We need to explain about Dispersion Compensation technique for the optical fiber communication using…

Q: What is the reason for using numerical methods?

A: Reason for using numerical.methods

Q: Provide three examples of when digital equipment could be useful. Did you give each change a lot of…

A: Certainly! Here are three examples of when digital equipment can be useful:

Q: How is a microchip fabricated, and what materials are commonly used in their manufacturing?

A: The fabrication process of a microchip, also known as an integrated circuit (IC), involves several…

Q: Power Electronics.   Write necessity of power supply and briefly describe different types of SMPS…

A: Power supply: It is an electronic device  that supplies electric energy to an electric loads the…

Q: Enumerate and define the classification of electronic communication

A: Communication is the way of expressing the thoughts in the form of messages from one end to the…

Q: 1.Describe the operation of (AGC)Automatic Gain COntrol 2. Describe the operation of dual…

A: 1) Automatic Gain Control (AGC) The output of demodulator is ac with amplitude of output signal is…

Q: Propagation delay is usually measured in a. milli-Watts O b. nano-seconds O. nano-Watts O d.…

A: We need to tell about unit of propagation delay.

Q: Solve the following operations and specify each calculations performed.   (10000101)2 = (…

A: In this question we need to convert the given number system into decimal.

Q: 1. Before the TRIAC is triggered on, the voltage across its ma in terminals is equal to the ___volta…

A:

Q: There are a number of importance of measurement and instrumentation system. Identify and explain 5…

A: importance of measurement and instrumentation system: Product development: Measurement and…

Q: What is the minimum distance between conduits in a junction box straight through pull? A. 6 times…

A: The correct option from the given options will be option D) 12 times. For junction box calculations,…

Q: What causes ground loops in an instrumen­tation system? What are the effects of a ground loop?

A: Given:

Q: Minimum of one half page typed with 12 font, single spacing. Make sure your name is on the paper.…

A: Solution   Electromagnetic testing (ET), especially eddy current testing, is commonly used to…

Q: Q4: Define the types of the communication systems forms and plot them and explain each one in…

A: Communication System : It is a system in which exchange the information between two node or points.…

Q: What is biomedical Instrumentation explain with examples

A: Biomedical Instruments  Bio-Medical Instruments is the application of knowledge and technology to…

Q: Can We usẽ a non-conducting tip STM? EXplälh your answer.

A: Note: We are authorized to answer the first question since the exact one wasn’t specified. Please…

Q: If the roots are lying to right side of s-plane the system is said to be critically stable stable…

A: If the roots of s plane lie in the right side of the s plane then system is?

Q: What are common methods for assessing the reliability of electronic components in a system, and how…

A: Assessing the reliability of electronic components in a system is crucial to ensure the proper…

Q: select one quickly Synchronous counter is ........... than asynchronous counter. a) faster, b)…

A: Synchronous counter is counter which clock input for each flip flop given at a time and output of…

Q: 2. The impubs resporae tnla dsereeime LT sytem is shown in Figure ti Cetemine and sketch e cpu yn of…

A:

Q: what is UNIFIED POWER FLOW CONTROLLER (UPFC) writing 200 words with diagram?

A: UPFC: Unified Power Flow Controller(UPFC) An electrical device called a unified power flow…

Q: Hello Sir. Good Evening. I have a question in my home work related Control System Lesson. The…

A:

Q: Question # 1 Discuss the technical working of walkie talkie. Your main focus should be on modulation…

A: Walkie Talkie:             Walkie talkies are handheld radios that communicate wirelessly on a…

Q: Draw the equivalent circuits of Class E chopper for the different quadrant operation and write its…

A:

Q: Describe the process for controlling maintenance requests. Should all requests be handled in the…

A: Maintenance is a basic part of every system or any operational thing because they need maintenance…

Q: a. indirect measurement b. measurement by optical means c. electro magnetic methods d. direct…

A: The solution is given below

Q: Give the reason for the following statements: 1) Using a Venturi flow sensor makes the measurement…

A: Any liquid coulmn upto a certain height has some potential energy. Venturi flow meters are devices…

Q: mmon objective when manufacturing printed circuit boards (PCBs) is a. maximizing the number of drill…

A: There are various objective when manufacturing PCBs these are  Aspect ratio  Copper clearance

Q: Explain PMMC with neat diagram.

A:

Q: How does TP4056 works? What is the purpose of red and blue lights in the components?

A: The TP4056 chip is a single-cell lithium-ion battery charger that protects the cell against…

Dielectric Breakdown

A dielectric is a material with low electrical conductivity and so is classified as an insulator. Dielectric materials are used to block the flow of electricity through them, allowing them to behave as an insulators. They can also be used to store electric charge or improve capacitance.Dielectrics have no free electrons for conduction because electrons are tightly bound to the nucleus. Because dielectrics contain a small number of electrons for electrical conductivity, they have a dipole. The two primary roles of dielectrics in electrical devices are insulation and electrical energy storage. An electric field polarizes the dielectric, and the polarization of the molecules allows dielectric materials to store charge.