Q2) The battery charger in the figure below includes a fully controlled single-phase bridge rectifier from a 50 Hz source. Powered by 200 V peak. Battery model includes 100 V voltage source series connection and resistor is12.Assuming uniformity, find a relation for the battery charging current in terms of angle a. L Batterymodel 10mH 10 v, =Vm sinøt 100

Q2) The battery charger in the figure below includes a fully controlled single-phase bridge rectifier from a 50 Hz source. Powered by 200 V peak. Battery model includes 100 V voltage source series connection and resistor is12.Assuming uniformity, find a relation for the battery charging current in terms of angle a. L Batterymodel 10mH 10 v, =Vm sinøt 100

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

I need the answer as soon as possible
2. For the following figure 1 employing the diode characteristics of figure 2. Determine a) DC load line b) Voltage across the resistance c) Instead of the DC source use a 10V AC source and find the AC load line. D1 charteritien DIN4002 V1 10V R1 2k R2 2k HINA Bever charateri -1A) Junetion diode characteristies, Ge and S Figure 1 Figure 2
P) For single - phase half-controlled bridge rectifier shown in the figure: 1. Derive a formula for mean load Voltage. 2. Draw the waveforms of Ve,is,iz, i3, iy and io assuming highly inductive Load and =45. T. T3 Dy
Q3: bridge rectifier circuit shown in Figure (1), with a forward diode resistance Rd=12, and Rd=0 for a reverse bias. The input voltage of the circuit is 240V and 482 load resistance. Determine: The de load current, the power input efficiency and the PIV rating is required for the diodes. D4 D1 Rd=10 RL=480 Vs Vrms D3 D2 Figure 1
Find Vpc if VAN = VBn = Vcn= 120 volts... Half-wave Three-phase Rectifier Conduction Waveform Periodic Time (T) A B A 90° 180° 360 450° 540 time 270° -V VAN VeN VaN VaN VEN Voc4 Voc 150 120° 270 390 510° time 30 Output Voltage Waveform
Q-2: A singie phase fiull-wave controlled rectifier is connected to RL load (R-15 ohm and 1.-20mH ). Vs- 240 and 50 Hz supply When the firing angle is a=55. Deternine: A} the average voltage and average current in the load. B) The form factor and ripple factor. C) Peak inverse voltage of the thyristor.
Design a full wave rectifier based on the circuit shown in Figure 5 below: N: N2 D3 RL ww US D, Figure 5 The required specification for the full wave rectifier circuit includes the peak output voltage of 5 V, deliver 100 mA to the load R1, and produce an output with a ripple of not more than 5 percent. An input line voltage of 220 V (ms), 50 Hz is available. Given V, =0.7 V. (d) Calculate v, (max). (e) Find the required turn ratio for the transformer. (1) Determine the Peak Inverse Voltage (PIV). (g) What is the effective load resistance? (h) Determine the required capacitance of the filter capacitor.
C4 R1 Vout For the precision rectifier circuit shown in Figure C4 what is the correct operation for the circuit if a Sine wave is 10k D1 R2 LM324 VEE applied to the input signal VIN? Vin D2 10k OUT V3 U1A Figure C4 A. When VIn is negative the circuit operates as unity voltage follower providing an in phase sine wave at VouT. When VIN is positive the circuit conducts but only to one diode drop, B. When VIn is negative the circuit operates as an inverting amplifier providing an inverted sine wave at VouT. When VIN is positive the circuit is driven to very close to zero due to amplifier gain reducing the diode drop voltage, c. When VIn is negative the circuit operates as an inverting amplifier providing an in-phase sine wave at VOUT. When VIn is positive the circuit is driven to very close to zero due to amplifier gain reducing the diode drop voltage, D. When VIn is negative the circuit operates as unity voltage follower providing an inverted sine wave at Vour. When VIn is positive the…
lution H.W5 Design the single-phase half wave controlled rectifier has a purely resistive load of R=1002 and the average output voltage varied from 30V to 120V.