Q2/ If a total of 35 MHz of band width is allocated to a particular FDD cellular system which uses 50 kHz duplex voice and control channels. If 0.7 MHz is dedicated for control channels and 10 MHz is dedicated for dynamic channels, determine an equitable distribution of control channels and voice channels in each cell for: (a) 7-cell reuse (b) 13-cell reuse.

Q2/ If a total of 35 MHz of band width is allocated to a particular FDD cellular system which uses 50 kHz duplex voice and control channels. If 0.7 MHz is dedicated for control channels and 10 MHz is dedicated for dynamic channels, determine an equitable distribution of control channels and voice channels in each cell for: (a) 7-cell reuse (b) 13-cell reuse.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

describe and compare the three methods ofgenerating SSBSC modulation
1. The VCO of a PLL free-runs at 7 MHz. The VCO does not change frequency until the input is within 20 kHz of 7 MHz. After that condition, the VCO follows the input to ±150 kHz of 7 MHz before the VCO starts to free-run again. Determine the lock and capture ranges of the PLL. (Ctrl)-
7. Describe the operation principle of the MOSFETS-based digital gate shown in Figure 3. In your answer, explain the need to use n-channel and p-channel MOSFETS for such digital gates. VDD Figure 3 8. A particular optical waveguide is made from silicon with an air upper cladding and oxide lower cladding. The measured effective index of the waveguide at 1300 nm is 2.2 and the measured effective index at 1550 nm is 2.0. (a) Assuming a linear relationship between wavelength and effective index in the form of
VLSI Wafer Yield Given the defect density D= and chip area A, use Murphy's yield model to estimate the chip yield. Calculate for D=0.5 defects/cm2 D=0.5 defects/cm2 and A=1.5 cm2 A=1.5 cm2.
3- If we increased 2 bits of the ADC quantizer, what is the improving in the SNR will be? Discussed your answer.
Construct an nmos circuit with depletion load with the function parameters are VDD = 5 V VTND = 0.4 V, VTNL = -0.6 V, (W/L)_L =1 Determine (W/L)_d of each transistor where output vo is 40 mv
please full answer
Explain how the arrangement of gates shown in Figure 5.34 gives an SR flip-flop. 5.7 Figure 5.34 Problem 5.7. R & & R Note: for problem 5.7, you need to use the figure above with 0/1 states to show the outputs Q and Q for different values of S and R. At last, you need to provide a truth table or a state table to show the relationship among S, R, Qt, Qt+1, Qt, Qt+1-
I need the drawing of the circuit. "convert the SOP (AND/OR) circuit diagram into one containing only NAND and NOR gates." I have included the picture of the SOP Circuit that needs to be converted. Please draw the circuit clearly and answer question 1 completly, thanks... quick response gets thumbs up
What is the chip rate of W-CDMA? a) 1.2288 Mcps b) 3.84 Mcps c) 270.833 Ksps d) 100 Mcps
Want to confirm with my own work
c) Draw a block diagram of a typical digital communications system including both transmit and receive paths and describe the nature of the signals generated by each of the blocks. Briefly describe what happens within the Modulator element and explain what is meant by the term 'up-conversion'.