voiteuses 60Q2/ If a total of 35 MHz of band width is allocated to a particular cellular system whichkHz duplex voice and control channels. If Q.5 MHz is dedicated for control channelsdistribution of controlis dedicated for dynamic channels,voice channels in each cell for 13-cell reuse.determine an equitableand 8 MHZchannels and

The total bandwidth allocated for the cellular system is 35 MHz.Control channels are allocated 0.5…

Q2/ If a total of 35 MHz of band width is allocated to a particular cellular system which kHz duplex voice and control channels. If Q.5 MHz is dedicated for control channels is dedicated for dynamic channels, determine an equitable distribution of control voice channels in each cell for 13-cell reuse. voice uses 60 and 8 MHZ channels and

Q2/ If a total of 35 MHz of band width is allocated to a particular cellular system which kHz duplex voice and control channels. If Q.5 MHz is dedicated for control channels is dedicated for dynamic channels, determine an equitable distribution of control voice channels in each cell for 13-cell reuse. voice uses 60 and 8 MHZ channels and

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Q.3: If 82C55 shown in Figure below is configured as follows: PA as input, PB as output, and PC as output and all ports in mode-0. a- Find the port address assigned to A, B, C, and control register. b- Find the control byte (word) for this configuration. c- Write a program to input the data from PA and find X & Y, then sent the result of X to port B and the result of Y to port C. X = A – 5, Y = A + 2 DO DO D7 07 Write signal Read signal WR RD CL AO A1 AO A1 A7 CU A15- CS 82C5SA
What is the expression for the following kmap? Assume the ? values are don't care values but if circled, they are 1. So assume 1100 has 1 instead of ?. What is the expression?
Consider the line of code below. analogWrite(11, 84); The voltage at pin 11 is turns on (at 5V for Uno) and off at 500 Hz. This PWM frequency is the default value for Arduino boards. How many microseconds is the voltage at pin 11 high?
Q3: A radio frequency signal was received with signal to quantization power ratio of 39dB and mathematical model of 4cos28.47nt 106, calculate 1- The number of bits every second. 2- The bandwidth and signaling rate. 3- The quantization noise power if the transmitted signal power of 0.04 watt.
a. Develop a time delay procedure for the 3.0 GHz Pentium-Core2 that waits for 50ms b. The 8255 shown in the following is configured as follows: port A as output, B as input, and port C (low and high) as output. 1. Find the port addresses assigned to A, B, C and the control register 2. Find the control byte (word) for this configuration. 3. Program the ports to input data from port B and send it to both ports A and C. Hint you can use delay in (a) if needed AO A3 A4 A5 A6 A7 10/M DO D7 IOW- IOR- A2 A1 DO D7 WR RD A0 Al OCS A B CL CH
1. Are the following statements correct or wrong? (a) Thyristors are used only for low voltage, low current applications. (b) MOSFETs are used for high frequency applications. (c) BJT is more efficient than IGBT in high power applications. (d) GTO requires very low current applied to its gate to be turn off. (e) IGBT is a voltage driven device. 2. Are the following statements correct or wrong? (a) Thyristors are preferred to be used in the output stage of 10W IMHz transmitter. (b) MOSFETs are preferred to be used for 1000 kW motor control circuit. (c) TRIAC is used for lighting dimmer circuits. (d) IGBT in high voltage de rectifier circuits (above 5kV level). (e) BJT is the fastest switching device in power applications. Choose the correct answer for the following questions (3-7): 3. The conditions which must be satisfied to turn on the thyristor with its current is more than its latching current are: (a) The anode is more positive than the cathode and a positive current pulse is…
transistor datasheet. 1. COMPLETE TABLE #1 Table 1 Parameters of BJT transistors Code type Ic [A] VCEO [V] PD[w] ft[MHz] encapsulated 2N2222A 2N3904 2N3906 NPN 0.2A 40V 0.625W 300MHz TO-92 MPS2907A PNP 0.8A 60V 0.4W 200MHz TO-92
A digital signal consists of two voltage levels: +5 volts and -5 volts. The transmitter sends the +5 volts signal with a probability of and -5 volts signal 3 with a probability of Calculate the power of the signal. 3
Answer the Question with the “arrow” sign based on the “bit error rate” questions. Don’t answer the bit error rate assignment only the channel capacity
Multiple Choice directions: Circle the letter of the answers that best answer the question. 1. For frequencies lower than 10GHZ, power amplifiers used microwave __? a. Oscillator b. All of the above c. Power tubes d. Transistors 2. The cathode material used in point contact diodes a. Tungsten b. Silicon c. Germanium d. GaAs 3. It is three port microwave device used to couple energy in one direction in a closed loop. a. Cavity resonator b. Circulators c. Directional coupler d. Isolators Note: Explanation is not needed just provide the correct answers for each number.
V:YE IC %Ov N a 46 l VOLTE moodle1.du.edu.om/mo Question 12 Not yet answered Marked out of 2.50 P Flag question Given a modulation index of 0.4 for an AM modulated signal, how much percent of the total power is carried by the carrier signal Select one: a. None b. 90 % c. 80 % d. 100 % e. 40 % Previous page Next page
3. In fixed channel assignment strategy, each cell is allocated a predetermined set of, a) Voice channels b) Control channels c) Frequency d) base stations