Q2: For the system shown in figure below, find the power that the wrbine (1) can extract The discharge through the pipe 3 is Q-0.23 m²/sec, 7-9810 N/m³. Neglect minor losses. 152m 85m d-150mm, 1-0.024 L-600m 2 60 m d-375 -0818 L-1200m Q-0.23 mm's d-300 mm, f-0 02 L-240 30m

Q2: For the system shown in figure below, find the power that the wrbine (1) can extract The discharge through the pipe 3 is Q-0.23 m²/sec, 7-9810 N/m³. Neglect minor losses. 152m 85m d-150mm, 1-0.024 L-600m 2 60 m d-375 -0818 L-1200m Q-0.23 mm's d-300 mm, f-0 02 L-240 30m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

9- a) b) c) d) For the transmission line shown, what are the appropriate appurtenance at point C. 300 m A L = 500 m B none of them air valve check valve blowoff Leave blank L = 1000 m 100 m 285 m L = 1000 m D 100 m
- Dekrmine the total head loss hf. from Å to o in the systen shomwn in the figure iF the discharge is 1. G0 mls. Assume f=0:02 for all pipes 450 mm o, GO0 m 9oomm ở , 90 m 구5Dmmd,40m D GUD mm,720m
I need the answer quickly
The steel pipe shown carries water from the main pipe A to the reservoir and is 2 inch in diameter and 240 ft long. What must be the pressure in A to provide a flow of 45 gpm? Clevation K00 t Water 7 50 F Open globe valve 90 bends (threaded)- Elevtion 20 fr 2 in galvanizcd pipe
Ql:-A cylinder of 1lft diameter and 2ft length floats in a tank that contains a liquid of specific weight .A u-tube manometer is connected as shown in figure. What is the weight of the cylinder whose upper the surface is flush with fluid surface PA--0.1 psi Water 2 ft Cylirder Gage fluid SG- 1.5 Sp wt.y 0.5 ft 02. w1
1. A pump station design fills a pressurized water tank by pumping water from a reservoir. The flow rate is 0.75 cfs. The pump is 10 feet above the reservoir, and the water tank is 100 ft above the pump. The pressure in the water tank is 10 psi. The suction and discharge lines are both (actual diameter) 6-inch Sch 40 steel (pipe roughness = 0.00015 ft). Use a kinematic viscosity of 1.21 x 10-5 ft²/s. Total pipe length is 200 ft. The suction line is 10 ft. You must account for friction loss, but you can neglect the minor losses. a. What is the head added by the pump in ft? b. What is the power added by the pump in HP (recall 1 HP = 550 ft*lb/s)? 110 ft 10 ft 0 ft
The steel pipe shown carries water from the main pipe A to the reservoir and is 2 in. in diameter and 240 ft long. What must be the pressure in pipe A to provide a flow of 50 gpm? 90°bends (threaded) 2 in galvanized pipe Elevation -90ft Open globe value Elevation = 20 ft - Water T-50°F
4G 3G 0 MID 202102.jp... Petermine the Diame ter of galvanized pipe Q4 to discharge 6 m/hr with a head length of pipe som required Loss 2om and with は2=115水6? (2-2)
ROBLEMS oment boreda-U ors 107 21090000 10 2-28M. A T VX 001 2 k/ft 12 ft Figure 2-86M 210800gmdo da snimissa .re- 2-28. Determine the reaction components for the simple beam of the taugh me ‒‒‒‒‒‒‒‒ Figure 2-81 Figure 2-81. 10 k EB-S onugi ads.90 1919 MIE-S Determine the reaction components for the simple beam of Figure 2-81M. 3 ft B 11 3-S A rea oor tion components 30 kN 3 m 1 m 10 kN/m 6m for for the rigid the Figure 2-81M 40 kN 3 m member in B
answer asap. need the answer within 1 hour. will upvote
QUESTION 4 The flow rate out of B is 0.03 m³/s Pipe 1 has a filter 1 (106) m²/s 9810 N/m³ and v= 10 A 50 mm -3 m 100 mm Determine the flow through pipe 1 in m³/s 5 2 m B V2 = 1.6- and globe valve Pipe 2 has a gate valve. The whole system is galvanized iron y = 2g
Flow In Closed Conduits 5. Water at 65F is pumped to a tank through a 750 ft 12-in diameter galvanized iron pipe and the flow is 4.5 cfs. (a) Determine the head lost due to friction. (b) How much power, in HP, is required to overcome this head loss? Answers: (a) _______________________________ (b) _______________________________