Q2: Five independent massages have bandwidths of 200 Hz, 300 Hz, 400 Hz, 500 Hz and 600 Hz, respectively. Each one of them is sampled at the Nyquist rate, and their samples are TDM and transmitted. What is the transmitted TDM signal rate (in Hz)?

Q: difference between measurement uncertanty and measurement error

A: Given : Need to find the difference between measurement error and uncertainty.

Q: What is the advantage and disadvantages Static and Dynamic characteristic of measuring instruments.…

A: Step-1->Static and dynamic characteristics are two important aspects of measuring instruments.…

Q: Is Mc microfarads?

A: Given, The abbreviation of mc =?

Q: hich of the following can’t be included in data required for coordination study? A)X/R ratio B)MVA…

A: characteristic curves of the fuses and breakers are generally analyzed in the coordination study

Q: In an electronic circuit, a. current remains the same through all the series components. b. voltage…

A: Note that,  In an electronic circuit, current remains same jn all series components and voltage…

Q: Sl.no Symbols Name of the components 1. 2. 3. 4.

A: here, the various symbols of the pneumatic circuits are given  which can be useful to make PLC…

Q: Khee Voltage of Ilicon semi nductor. (without Your answer A condition where zero (0) volt is less…

A: 1) Knee voltage of silicon semiconductor is 0.7

Q: & Prove That %3D

A: Resonance Resonance is the condition when the voltage across a circuit becomes in phase with the…

Q: 1. WRITE THE CKT. DIAGRAM OE FOUR BASIC TYPES OF SERIES CKT.

A: Series circuit A Series Circuit occurs when two or more loads are linked in series. If one load or…

Q: With neat diagram explain the construction and working of CRO.

A:

Q: In static characteristics, is defined as the difference between the true value applied to a…

A: in static characteristics, Accuracy is defined as the difference between the true value applied to a…

Q: What is the percentage of carbon residue? What is the importance of carbon residue?

A: 1) The carbon Residue value of fuel depends on the refinery processes employed in its manufacture.…

Q: 1.verify (Kc) and (KUL)) ?

A:

Q: Given the information appearing in Figure beside (assume Ic=IE) determine: (a) Ic. (b) VE. 18 V (c)…

A: Disclaimer:  Since you have asked multipart questions, we will solve the first three subpart for…

Q: The AND-OR implementation of PAL is having O a. Programmable AND array and Programmable OR array Ob.…

A: Given: Brief description: In the above given question they are discussing about the working of the…

Q: In a rectifier circuit , DC output voltage and RMS output voltage is  0.3 V & 0.6 V respectively.…

A:

Q: Difference in the digital and the analog systems

A: Both digital and the analog systems are used to transmit and received information (or signals). The…

Q: Label the parts of Tubular Steel Poles

A: Steel tabular poles are not commonly used poles these poles are used when there is need of low cost…

Q: What is UHV and EHV?

A: EHV stands for Extra High Voltage transmission line whereas UHV stands for Ultra High Voltage…

Q: A transistor is used as a switch and the waveforms are shown below. The parameters are given as…

A: Given  Transistor as switch and waveforms as shown  Vcc=200 vVCE(sat)=1 vICS=100 AICEO=1 mArise time…

Q: Briefly describe how a distance can be measured by the method of phase comparison

A: From the method of phase comparison, the distance is measured indirectly by determining the number…

Q: Identify each characteristic curve by the type of FET that it represents. Ip -VGS +VGs

A: For N channel JFET, the VGS voltage is negative and the saturation current IDs we obtain at Vgs.

Q: Identify the elements considered for the Voltage Drop calculations in D.C distribution system. O a.…

A: Inductive reactance (XL) = 2πfL  Shunt admittance (Yc)= 2πfC In dc distribution, the frequency of…

Q: Q1. Convert following numbers in given radix system: a. (173)10 into hexadecimal b. (2E3)16 into…

A:

Q: Experiment Title SIGNAL GENERATORS

A: WE have to discuss signal generator, The sine wave generator represents the largest single category…

Q: From the table, what is the circular mils for the following: a. 14 AWG a. 10 AWG b. 30 AWG c. 20 AWG

A:

Q: Discuss the operation of a multi-meter

A: Solution :    In the above question they are interested to know the operation of a multimeter.   As…

Q: 3. Explain the successive approximation type ADC with neat schematic diagram.

A: Successive approximation ADC: The successive approximation ADC is a type of converter that converts…

Q: In FET, An outward-pointing arrow represents ___. Choose the correct answer below: a.N-type…

A:

Q: Use block diagram formula

A:

Q: 3) What is the dropout ratio? What is the advantages of dropout ratio in power systems. (min 1 page)

A: A pick-up and drop-out ratio terms related to protective relays. The pickup current of a circuit…

Q: Question : Explain the concepts of lattice matched hetero-structure. Don’t copy other works.…

A: It is asked to explain the concept of lattice matched hetero-structure.

Q: A company is producing a certain type of circuit breaker. The fixed cost is (450 000$), and the…

A: Given data, Fixed cost of CB, FC=$450000 Variable cost, VC=$33/unit Breakeven at 37500 units.

Q: Give the title proposal about renewable energy atleast 5 title Bachelor electrical engineering

A: Renewable Energy:- Renewable energy is produced using resources found in nature that are not…

Q: diff b/w aproximated & Interp0leted Curves. (Brief explanation with sketches)

A: Graphs are the pictorial representation of the system when we vary one quantity with respect to the…

Q: Identify the elements considered for the Voltage Drop calculations in D.C distribution system. О а.…

A: For DC distribution, voltage drop across the element?

Q: What is the UPS

A: A uninterruptible force supply (UPS) is a gadget that permits a PC to continue to run for in any…

Q: 9Vpk pk Vin Vout 1.25 2.25 3.75 4.50 -1.25 -2.25 -3.75 -4.50

A: We need to find out output voltage for given input values in clamper circuit .

Q: in zeq 1 where did you get 210.949 from?

A: Student is asked to explain from where did get ZB 210.949 from?

Q: Give the concise definition or process of getting the equations in each loop/mess (Mesh Analysis) in…

A: Let us try to understand the concept of mesh analysis in this answer.

KVL and KCL

KVL stands for Kirchhoff voltage law. KVL states that the total voltage drops around the loop in any closed electric circuit is equal to the sum of total voltage drop in the same closed loop.

Sign Convention

Science and technology incorporate some ideas and techniques of their own to understand a system skilfully and easily. These techniques are called conventions. For example: Sign conventions of mirrors are used to understand the phenomenon of reflection and refraction in an easier way.