7:1) O ZY9O Q1 15-3-2021.j.->Q1) At point A, the four forces Fn, Fc, Fp and Fg act, the lines of action for these forces aregiven by the straight lines AB, AC, AD and AE, as shown in Figure 1.Coordinate the points are:yABDF412cmcmFigure 1The magnitudes of the forces are: Fy= 7 KN, F= 3 KN, F- 9 KN and F- 13 KN.Represent this force F acting on the point 4 as a Cartesian vector and determine its direction.Q2) Figure 2 shows a rope that is stretched between points A and C, there is mass m at pointB. Given values: m= 20 kg, =2 m, d= 3 m, a= 30", y-60".Determine the followings:a) What are the values of lengths Lan and Lac must be selected according to the given angles aand y?b) What are the values of forces Fay and Fre in the rope sections AB and BC?Figure 2Bg

Hello. Since you have posted multiple questions and not specified which question needs to be solved,…

Q2) Figure 2 shows a rope that is streteched between points A and C, there is mass m at point B. Given values: m= 20 kg, h= 2 m, d- 3 m, a- 30", y-60". Determine the followings: a) What are the values of lengths Las and Lac must be selected according to the given angles a and y? b) What are the values of forces Fas and Fne in the rope sections AB and BC? Figure 2 B.

Q2) Figure 2 shows a rope that is streteched between points A and C, there is mass m at point B. Given values: m= 20 kg, h= 2 m, d- 3 m, a- 30", y-60". Determine the followings: a) What are the values of lengths Las and Lac must be selected according to the given angles a and y? b) What are the values of forces Fas and Fne in the rope sections AB and BC? Figure 2 B.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

18 only
What is difference in loop and mesh?
Consider two infinitely long parallel wires. The wires are separated by a distance of 10 cm. Both wires carry a current of 5 A but in opposite directions. Compute the force per unit length on wire 2 due to the current in wire 1.
13 - Which of the following is true about the magnetic field in the Biot-Savart law?I. is inversely proportional to r.II. It is inversely proportional to r2.III. It is directly proportional to the current. A) Yalnız I B) II ve III C) Yalnız III D) I ve III E) Yalnız II
H.W-3 1- Why the capacity of SG is taken in kVA and for IM is taken in kW? 2- Explain the effect of changing the load (inductive-capacitive- resistive) on SG terminal voltage? 3- Why the magnetization curve of SG is similar to the B-H curve of armature steel core? 4-Write a short report about Blondel two-axis theory for SG?
4- Which of these are types of normal stresses? a. Tensile and compressive stresses b. Tensile and thermal stresses c. Shear and bending 5- If a material has identical properties in all directions, it is called a. Elastic b. Plastic c. Isotropic d. Homogeneous 6- When a wire is stretched to double in length, the longitudinal strain produced in it is a. 0.5 b. 1.0 c. 1.5 d. 2.0
The figure of merit which describes the overall behavior of the wire under stress isdetermined from?Select onea elastic modulus b gauge resistancegauge factorastic factor
A certain wire is having length of 68 m on a winter day when the temperature is -29 °C. How much longer (in mm) is the wire on a summer day when the temperature is 27 °C? (Consider a 14 x 10-5 (°C) 1, for the material of the wire)
A P KN Refer to the figure. d₁ 0.9 m Force P is 60 kN and each force Q is 125 kN. Q KN B Add your answer Integer, decimal, or E notation allowed Q KN The diameter d₁ = 30 mm and diameter d₂ = 50 mm. d₂ 1.2 m What is the normal stress in rod BC in MPa? Round to the nearest integer and enter the magnitude only. C
Consider the magnetic circuit given in below figure with parameters: u=105 Ho, d1=7.2 cm, d2-6.6 cm, d3=5.5 cm, d4=0.4 cm and N=493. Assume that all branches have the same cross-sectional area of 5 cm². Magnetic flux density is 0.4 Wb/m2 in the air gap. Based on the given configuration calculate the current I in [AJ in the coil. d2 dg Tolerance + 0.1 relative Answer:
Please compute the torque required for this problem. Thankyou.