Q2) A3- phase 50 Hz transformer has a delta connected primary and star connected secondary, the line voltage being 22000 V and 400 V respectively. The secondary has a star connected balanced load of 0.8 power factor lagging. The line current in primary side is 5 A. Determine the current in each coil of the primary and each secondary line. What's the output of the transformer in Kw.

Q2) A3- phase 50 Hz transformer has a delta connected primary and star connected secondary, the line voltage being 22000 V and 400 V respectively. The secondary has a star connected balanced load of 0.8 power factor lagging. The line current in primary side is 5 A. Determine the current in each coil of the primary and each secondary line. What's the output of the transformer in Kw.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

In single phase transformer, if the secondary turns N2 is greater than the primary turns N1, then what is the relation between V2 and V1? O a. V2 = V1 O b. V2 > V1 O c. V1 < V2 O d. V2 < V1
Which of the following is the correct equation for calculating the rated current for a single-phase transformer? A. I=va/e b.I=sc/e c.a/e d.e×z/e
The number of turns on the primary and secondary windings of a 1- transformer are 380 and 40 respectively. If the primary is connected to a 2.2 kV, 50-Hz supply, then the secondary voltage on no-load is
Three single phase 11000/220 V transformers are connected to form 3-phase transformer bank. High voltage side is connected is star, and low voltage side is in delta. What are the voltage ratings and turn ratio of 3-phase transformer? 19052 a) V, 50 220 11000 381 c) V, 50 √3 b) d) 19052 220 V, 50√3 11000 220 7.50
Q2/A/ What are the conditions for satisfying parallel operation of single phase transformer? Deduce an expression for the load shared by the two transformers in parallel when the transformers have equal voltage ratio? Prove your answer. B/ A 50 KVA, 2300/230 V, 60 11z transformer has a high voltage winding resistance of 0.650 and a low-voltage winding resistance of 0.0065 2. Laboratory tests showed the following results: Open circuit test: V = = 230 V, I =5.7A, P = 190 W Short circuit test: V-41.5 V, I-21.7 A, P-No wattmeter was used. 18 (2) Compute the value of primary voltage needed to give rated secondary voltage when the transformer is connected as a step-up one and is delivering 50 KVA at a power factor of 0.8 lagging. (b) Compute the efficiency under conditions of part (a).
2- Determine the number of turns per-phase in each winding of a 3-phase transformer with a ratio of 20000/2000v. to work on a 50Hz network. The high-voltage winding is delta connected and the low-voltage is star-connected. Each core has a gross sectional area of 560 cm². Assume a flux density of about 1.2 wb/m². [1490/86]
B- the eddy current losses of 400V, 50 Hz transformer is 1600W and the total iron losses i 2500W. calculate the iron losses at 200V, 25 Hz.
The test results of a 5 kVA, 400/200 V, 50 Hz, single phase transformer are as follows. O.C. Test: 400 V, 1 A, 50 W, H.V. side S.C. Test: 12 V, 12.5 A, 60 W, H.V. side Find the full load efficiency and regulation when the power factor is 0.8 lagging.
A 120 kVA, 1350/330 V single phase transformer has the following parameters: R1 = 0.34 Q, X1 = 0.59 0, R2 = 0.014 Q, X1 = 0.029 Q, Rc = 380 and Xm = 320 Q. The no load current is 4.7 A at a power factor of 0.36 lagging and the no load losses are 4.6 kW. For a full load and 0.9 power factor lagging with 300 V load terminal voltage, determine (a) equivalent circuit parameters referred to primary side, (b) percentage regulation and (c) full load efficiency. O:01 AM
c) A 100 kVA, 4500/250 V, 50 Hz single-phase transformer has 100 secondary turns.Determine: i.The primary current.ii.The secondary current.iii.The number of primary turns.
Q/A single-phase transformer with a capacity of 100 kVA and a voltage of 2000/400 and the equivalent circuit elements are: As follows R1 = 0.1 02 x1 = 0.2 2 R2 = 0.25 2 X2 = 0.75 2 RO = 500 XO = 150 Q and feeds a load of 90 kVA at a voltage of 2000 volts and a power factor of 8.0 in delay. Calculate voltage and current Primary Royl ww JX eql
Following are the results of a test carried out on a 230/600 V single phase, 7.5 kVA transformer. O.C. Test : 230 V, 1.2 A, 280 W, on L.V side S.C. Test : LV winding is shorted. 26 V, 11A, 155 W, H.V. Both the full load efficiency and full load regulation of the transformer on the side are 0.8 lagging p.f Search on.