Q2) A parachutist of mass 60 kg jumps out of a stationary hot air balloon. Use numerical method to plot the velocity-time relationship and compute the terminal velocity. The drag coefficient is equal to 12 kg/s. Employ a step size of 4 s for the calculation. Repeat the solution by using Analytical method for five steps only. Based on your results, discuss which method is more exact?

Q2) A parachutist of mass 60 kg jumps out of a stationary hot air balloon. Use numerical method to plot the velocity-time relationship and compute the terminal velocity. The drag coefficient is equal to 12 kg/s. Employ a step size of 4 s for the calculation. Repeat the solution by using Analytical method for five steps only. Based on your results, discuss which method is more exact?

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A vertical one-link manipulator is illustrated in Figure Q1b. Assume that there is viscous friction at joint 0, determine the dynamic model of this manipulator through Newton-Euler approach. mg Coefficient of Friction, u Figure Q1b
The position of a particle is given by s = 0.30t³ -0.70t² - 2.50t + 4.99, where s is in feet and the time t is in seconds. Plot the displacement, velocity, and acceleration as functions of time for the first 8 seconds of motion. After you have the plots, answer the questions as a check on your work. Questions: 0 1 When t = 1.8 sec, V = When t = 6.5 sec, V = ●+ 2 i i +s, ft ft/sec, ft/sec, The positive time at which the particle changes direction is i a = a = i i sec. ft/sec² ft/sec²
This question is a short free-response question. Show your work for each part of the question. A puck of mass m, slides across a horizontal surface and collides with a stationary, nonuniform rod that is pivoted about its left end in three configurations, as shown. In each case, the puck travels with the same initial velocity v, and collides with the rod at time te . In Case 1 the puck rebounds away from the rod, in Case 2 the puck comes to rest after the collision with the rod, and in Case 3 the puck sticks to the rod. Frictional effects between the rod, puck, and floor, as well as frictional effects of the pivot, are small enough to be considered negligible. Case Piyot Case 2 Pivot ---------------- Case 3 (a) On the graph below, sketch and label the two quantities as a function of time for Case 1. You do not need to calculate values for the y-axis, but the same vertical scale should be used for both quantities. i. Angular momentum of the puck ii. Angular momentum of the rod Label the…
The wedge system shown is used to lift an object with mass 312 kg. If the friction coefficient between two blocks, and between a block and a surface, are 0.2 and 0.35, respectively, what is the minimum force P required such that the object is about to be lifted? Assume weights of the blocks to be negligible compared to lifted weight. Parameters: 3AB kg = 312 kg 6C° = 63° 3D° = 34° 4E° = 45° 60° 3AB kg A 3Dº This is not property as if it were your B 4E° your prope C P
Determine the drag force (in kN) exerted on a high-rise building if the frontal dimension has a height of 80 m and a width of 25 m. The wind speed is 45 mi/hr. Let drag coefficient, CD = 1.4 and ρair = 1.2 kg/m3. Round off your answers to three (3) decimal places.
At a given instant the roller A on the bar has the velocity v = 4 m/s and acceleration a = 7 m/s? . (Figure 1) Determine the bar's angular velocity at this instant measured counterclockwise. Express your answer using three significant figures. Enter positive value if the angular velocity is counterclockwise and negative value if the angular velocity is clockwise. Wbar = 6.67 rad/s Submit Previous Answers v Correct Figure 1 of 1 Part D Determine the bar's angular acceleration at this instant measured counterclockwise. Express your answer using three significant figures. Enter positive value if the angular acceleration is counterclockwise and negative value if the angular acceleration is clockwise. vec 30 0.6 m abar = 23.817 rad/s? 30 Submit Previous Answers Request Answer X Incorrect; Try Again; 3 attempts remaining
During a hydraulics laboratory experiment using a venturi meter and orifice meter to calculate the coefficient of discharge, the following results were obtained. Using the following data produce the results table from the lab results and data given. Table of Results 1 2 3 4 5 HV = (h1 - h2) m HO = (h6 – h7) m Q m3/s HV1/2 HO1/2
Consider (Figure 1) Figure 60° 20 ft < 1 of 1 ▼ Part A Determine the minimum initial velocity up at which the ball must be kicked in order for it to just cross over the 8-ft high fence. Express your answer using three significant figures and include the appropriate units. Ti μA 3 C ? v0 = Units Submit Request Answer Part B Determine the corresponding time t at which the ball reaches the fence Express your answer in degrees using three significant figures. IVE ΑΣΦ 11 vec C ? Value
Find the equations of internal moments, the angle and deflection of the beam, all as a function of the variable x (axial axis of the beam). Graph these equations. Include your procedure and the code you used to generate the graphs 6 kN/m 20 kN B -1.5 m 3 m- 1.5 m
Consider (Figure 1). Figure Vo 00 6 m 3 m ▼ Part A Determine the minimum initial velocity vo at which the ball must be kicked in order for it to just cross over the 3-m high fence. Express your answer using three significant figures and include the appropriate units. v0 = Submit Part B 00 = μА Submit Value Request Answer Units Determine the corresponding angle o at which the ball must be kicked. Express your answer in degrees using three significant figures. AΣ vec Request Answer **** *** ? ***** ***** ? O
Fluid often passes through pores in cell membranes or cell layers. The dimensions are small and the velocities low, so viscous forces dominate (low Reynolds number). Use dimensional analysis, or an approximate method of analysis based on the viscous flow equations, to determine the scaling law that expresses the dependence of the pressure drop across a pore (ΔP) on the flow rate through it (Q). The other parameters that are given include the pore radius, R, and the viscosity of the fluid, μ. The membrane itself should be considered infinitesimally thin so that its thickness does not influence the pressure drop.
Please prioritize your attention on "determining the weight of the beam." The main focus should be on the weight of the beam. Your task is to EXPAND THE EXPLANATION OF THE EXPERIMENT regarding the determination of the beam's weight. See attached pictures.