Q2) A machine component is subjected to fluctuating stress that varies from 60 to 120 N/mm. The corrected endurance limit stress for the machine component is 270 N/mm?. The ultimate tensile strength and yield strength of the material are 600 and 450 N/mm2 respectively. Find the factor of safety using i) Goodman line Also, find the factor of safety against static failure. ii) Soderberg line) iii) Gerber theory)

Q2) A machine component is subjected to fluctuating stress that varies from 60 to 120 N/mm. The corrected endurance limit stress for the machine component is 270 N/mm?. The ultimate tensile strength and yield strength of the material are 600 and 450 N/mm2 respectively. Find the factor of safety using i) Goodman line Also, find the factor of safety against static failure. ii) Soderberg line) iii) Gerber theory)

Name: Q2)A machine component is subjected to fluctuating stress that varies
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: Q2)A machine component is subjected to fluctuating stress that varies from 60 to 120 N/mm.The corrected endurance limit stress for the machine component is 270 N/mm. The ultimatetensile strength and yield strength of the material are 600 and 450 N/m

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

In the graph, the module of toughness can be shown to be represented by: A) The area associated with necking B) The rectangular area label yielding C) The triangular area in the elastic region D) The sum of the entire shaded area under the curve
a) i) The numerical value of plastic section modulus of the solid rectangular section is mm^3 ii) The numerical value of plastic moment of the solid rectangular section is N.mm b) The numerical value of ?t can be calculated as mm
4. We want to draw a 7.5 mm diameter copper wire having a yield strength of 140 MN.m²² into a 6 mm diameter wire. Will the drawn wire break during the drawing process? Strength (MN.m-2) 600 500 400 300 200 100 0 0 Tensile strength 20 Yield strength % Elongation 60 40 Percent cold work 80 100 90 80 70 60 50 40 30 20 10 100 % Elongation
Q6: The following stress-strain curve is for a copper alloy (Figure 1 and Figure 2). At fracture, the total length was 53 mm, and the diameter was 10 mm. The initial length and diameter were 50.8 mm and 12.8 mm respectively. Determine: a) the 0.2% offset yield strength b) the ultimate tensile strength UTS c) the modulus of elasticity E d) engineering stress and strain at fracture e) true stress and true strain at UTS f) true stress and true strain at fracture (N) Load (N) 60000- 50000 40000- 30000- 20000 10000 0- 40000- 30000 20000 10000- 04 10 15 20 Change in length (mm) Figure 1. Load-Al curve for a copper alloy 0 5 0.2 0.0 Change in length (mm) Fracture region Figure 2. The magnified load-Al curve for the same above copper alloy to show the elasticity
4. The yield strength of material is fy = 700 MPa. If the stress state in the most stressed point in our structure is as pictured on the right, is the structure safe or will yielding occur? a) Use Tresca's yield criterion b) Use Von Mises' yield criterion. 200 MPa 150 MPa 500 MPa
please solve it all to give you the like
The First half of this question has been answered. (First 3) Needing help with the last part. Answered: 1) Solid / Ductile Material 2) Spring Constant: K = 05 = 250 N/m 3) Time Threshold: 5 seconds Unanswered / Need: Viscoscity, Charasteristic Frequency & What real world model charasteristic does this describe?
Project 3: Table 4 shows the fatigue data of a ductile cast iron to be used for an automobile axle that rotates at an average rotational speed of 750 revolutions per minute: Tuble 4: Fuligue dula of u duclile cust iron Stress Amplitude (МPa) Cycles to Failure 248 1 X 105 236 ЗX 105 224 1X 106 ЗX 106 1 X 107 3 X 107 1 X 108 3 X 108 213 201 193 193 193 a) Make an S-N plot (stress amplitude versus logarithm cycles to failure). b) What is the fatigue limit for this alloy? c) Determine the fatigue lifetimes at stress amplitudes of 230 MPa and 175 MPa? d) Discuss your results.
Nilo phi.
6. A railroad track is laid at a temperature of 10°C with gaps of 0.008 m between the ends of the rails. The rails are 20 m long. The coefficient of thermal expansion is 11.7 x 10-6 m/m °C and E=22 GPa. a) Determine the actual deformation of the rails that will result from a temperature of 65 °C. b) Determine the corresponding strain due to this deformation. c) Determine the thermal stress if they are prevented from buckling (or sidewise bending).
The stainless steel specimen is shown in Figure 3 with tensile engineering stress-strain behaviour. a)Calculate true stress at an engineering strain of 0.04.
Please help. Do not just guess. Prove your answer. I will give a good feedback. thank you :)