Q2\ A compound bar consisting of bronze, aluminum, and steel segments is loaded axially as shown in the figure. Determine the maximum allowable value of P if the change in length of the bar is limited to 2 mm and the working stresses prescribed in the table are not to be exceeded.

Q2\ A compound bar consisting of bronze, aluminum, and steel segments is loaded axially as shown in the figure. Determine the maximum allowable value of P if the change in length of the bar is limited to 2 mm and the working stresses prescribed in the table are not to be exceeded.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: The aluminum machine part is subjected to a moment of 75 kNxm. Determine the bending stress created…

A: Solution:Given: The moment acting on the section is M=75N.m which is sagging, so the topmost fiber…

Q: A 10 cm diameter solid alumin Assume that L=0.5 m. The yiel a) Normal stress due to bending caused…

Q: A round aluminum alloy rod has a diameter of 12.5 mm and 1 m length. Its ultimate strength is 155…

A: Given:- Diameter of the round aluminum alloy rod = 12.5 mm Length of the aluminum rod = 1 m…

Q: A threaded round steel bar is subjected to a tota axial pull of 8000 lb. If the diameter of the…

A: Take diameter of threaded portion≈unthreaded portionso,Stress=PArea

Q: SITUATION. As shown in the figure below, a rigid bar with negligible mass is pinned at O and…

Q: An aluminum alloy [E = 70 GPa; V = 0.33; a = 23.0×10-6/ºC] pipe is subjected to a tensile load P.…

A: To Find :- magnitude of load P

Q: Question 1: The rubber band given below is subjected to the following tensile loading. Calculate the…

A: Allowable tensile strength of rubber, Allowable shear strength of steel, Tensile force, Width of…

Q: Question 4. Three wires are used to suspend the plate shown. Aluminium wires used at A and B with a…

Q: 1 1 Portions of a x-in. square bar have been bent to form the two machine components shown. Knowing…

A: A square section of dimension in2 is bent into two sectionsSquare sectionDiamond sectionThe…

Q: (Problem 2.126 from the text book) Two solid cylindrical rods are joined at B and loaded as shown.…

A: Given Esteel =29 ×106 Psi Ebrass = 15×106 psi Note 1 psi = 1 lb/ in2

Q: 12 ID 12 Draw the Mohr's circle. Find the stresses on the plane shown. Fill in the blanks and table.…

Q: SITUATION. As shown in the figure below, a rigid bar with negligible mass is pinned at O and…

Q: 780 MPa; v = 0.46] rod has a diameter of 90 mm before lo d must not exceed 92 mm when loaded. What…

A: Given data - Young's modulus (E) = 780Mpa Poisson's ratio (v) = 0.46 Diameter of rod (d) = 90 mm…

Question

Q2\ A compound bar consisting of
bronze, aluminum, and steel
segments is loaded axially as shown
in the figure. Determine the maximum
allowable value of P if the change in
length of the bar is limited to 2 mm
and the working stresses prescribed
in the table are not to be exceeded.
A (mm') E (GPa) Ow (MPa)
=TTT
Aluminum
Bronze
450
83
120
3P
Bronze
Steel
2P
P AP-
Aluminum
600
70
80
Steel
-0.6 m→l-
- 1.0 m-
H-08 m-
300
200
140

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1 Introduction

VIEW

Step 2 Solution

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

1. The assembly has the diameters and material makeup indicated. If it fits securely between its fixed supports when the temperature is T; = 70°F, determine the average normal stress in each material when the temperature reaches T2 = 130°F. 304 Stainless steel - 2014-T6 Aluminum -C 86100 Bronze A 12 in. 8 in. D C 4 in. -4 ft- 6 ft- 3 ft
PROBLEM 01: Hollow bar length is 1.40m long and tube length is three-fourth as long as the bar. Torque T=1100N.m acts at the free end of the bar. Both the bar and tube are made of an aluminum alloy with shear modulus of w ww elasticity G=27GN/m². Given that dl=35mm, d2=45mm, d3=60mm, d4=70mm. Determine the following: a. Maximum shear stress in both the bar and tube b. Angle of twist at the end A of the bar. (In degrees) Tube Fixed plate End plate Tube d3 d1 d2 d4 Bar Cross-section of the bar and tube
What maximum load P can be applied without exceeding an allowable stress of 70 MPa for aluminum or 120 MPa for steel? Can a larger load P be carried if the length of the aluminum rod is changed. the length of the steel portion being kept the same? If so, determine this length
The solid rod has a diameter of 20mm. Find the following: Angle of twist at C with respect to A (in radians) Angle of twist at B with respect to A (in radians) Maximum shear stress at A (in MPa) (Shear stress at support, at a point 7mm from center. (in MPa) A-36 steel with the following properties: Modulus of Elasticity, E = 29x10^3 ksi or 200 GPa Shear Modulus/Modulus of Rigidity, G = 11.5x10^3 ksi or 79.3 GPa Poisson's Ratio, nu = 0.260 Temperature Coefficient for thermal expansion, a = 6.6x10^-6/°F or 11.7x10^-6/°C
A compound bar consisting of bronze, aluminum, and steel segments is loaded axially as shown in the figure. Determine the maximum allowable value of P if the change in length of the bar is limited to 2 mm and the working stresses prescribed in the table are not to be exceeded. E=200 GPa A=D300mm? L=3m 2m 2 m 3m 1.5m Match each tem to a choice
Required information Consider the loading shown. The allowable normal stress for the steel used is 160 MPa. 0.8 m 50 kN/m B -2.4 m- 0.8 m For the selected design, determine the actual value of Om in the beam. (Round the final answer to one decimal place. You must provide an answer before moving to the next part.) The actual value of om in the beam is 160 MPa.