Q2) A 110-V RMS, 60Hz source is applied to a load impedance Z. The apparent power entering the load is 120 VA at a power factor of 0.707 lagging. Assuming the voltage source is the reference phasor and has the zero phase angle, i.e., the phasor of voltage source is 110/0° V (RMS). Find: (a) the complex power (b) the rms current phasor Irms supplied to the load, (c) Z, and (d) assuming Z is a combination R and jwL, find the values of R and L.

Q2) A 110-V RMS, 60Hz source is applied to a load impedance Z. The apparent power entering the load is 120 VA at a power factor of 0.707 lagging. Assuming the voltage source is the reference phasor and has the zero phase angle, i.e., the phasor of voltage source is 110/0° V (RMS). Find: (a) the complex power (b) the rms current phasor Irms supplied to the load, (c) Z, and (d) assuming Z is a combination R and jwL, find the values of R and L.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Q2: Write a lecture for teaching the complex power fed to an (R-L) load fed from an AC power source of sinusoidal voltage and current waveforms, describing its three components, their waveforms, their power triangle, and units.
Electrical load that draws current whose impedance varies throughout the cycle of the input ac voltage waveform is known as nonlinear load. True False
The following phasor diagram is: a. The phasor diagram of SG when it is running at lagging power factor b. The phasor diagram of SM when it is running at leading power factor c. The phasor diagram of SM when it is running at lagging power factor with the existence of RA d. The phasor diagram of IM when it is running at lagging power factor
8.49 In the circuit shown in Fig. P8.49, a generator is connected to a load via a transmission line. Given that : (4 + j2) №2, and Zload = (40+ j30) 2: = Rs = 102, Zline S
Problem 3-An AC circuit is shown. The frequency is 1000 Hz. The source voltage is v(t) = 10 cos(2x1000) of clouent a) Find the impedance seen by the voltage souree b) Find the phasoj current delivered by the source. c) Find the phasor voltage across the resistor, Vr. d) Find the sor voltage across the capacitor, Ve e) Find the voltage across the capacitor, v.(1). 4 kQ 10/ 0 sine 1 kHz C C1 53 nF
For the circuit shown below, Given that V= 10020°V, and I 304Z30 Ams. %3D then the values of P2 rms and Q3 are given as Is P2 600 VAR Сарacitive 800 W 1200 W 1400 VAR Vs Inductive
Solve for step by step process with complete solutions
4) Given: R = 700-N, Xc = - j 500-N, e(t) = 150 sin(wt) V Find: a) Total impedance of the ckt. b) Total current in phasor and sinusoidal form c) Voltage drop across the resistor and capacitor in phasor and sinusoidal form d) Total Power and Power factor
Consider the situation shown in (Figure 1). A 1000-V-rms source delivers power to a load. The load consumes 140 kW with a power factor of 55 percent lagging. Time remaining: 00:07:30 Electrical Engineering Consider the situation shown in (Figure 1). A 1000-V-rms source delivers power to a load. The load consumes 140 kW with a power factor of 55 percent lagging. 1- Find the phasor II, assuming that the capacitor is not connected to the circuit. Enter your answer using polar notation. Express argument in degrees. 2-Find the value of the capacitance that must be connected in parallel with the load to achieve a power factor of 100 percent. Express your answer to three significant figures and include the appropriate units. 3-Usually, power-systems engineers rate capacitances used for power-factor correction in terms of their reactive power rating. What is the rating of this capacitance in kVAR? Express your answer using three significant figures. 4-Assuming that this…