Q1:A)Write the command to draw Figure below by using Auto CAD program (Relative Coordinate Method). All dimensions in millimeter 50 30 135 42,43 Start point 20,20

Q: 3.0 A uniform horizontal 300.0 N beam, 5.00 m long, is attached to a wall by a pin connection that…

A:

Q: 10. Which of the following is correct in dimensioning a drawing?

A: 10. Dimensions should be placed in between the views.

Q: Draw in full scale front view ( indicated by the arrow F), top view and left-side view of the…

A: to find top , front and left view

Q: Locate the centroid of the plate area shown below: (All units are in mm). Ø200- Ø150 300 300 Ø50 50…

A:

Q: Subject: Engineering Drawing or AutoCAD Instruction: Draw the 2D Orthographic Projection (Front,…

A: Asked: To draw the orthographic projections of the given object.   The following tools are used to…

Q: TOP VIEW FRONT VIEW RIGHT SIDE VIEW PROBLEM:

A:

Q: .500- 5.02 4.98 0.50 4.00±.02- 50 X 45° + 2.000 2. WHAT IS THE FARTHEST THE LEFT EDGE OF THE Ø.50…

A: Farthest distance = (outer dimension - minimum distance of centre to centre hole)/2

Q: y 74 mm 36 mm - 36 -+ 36 mm mm Answer: y = i mm

A:

Q: The ABC rod is supported from point B and is in equilibrium with a force F1 = 12KN applied from…

A: Given Data: The equilibrium force F1 is, F1=12 kN The shear strength at pin B is, τs=350 MPa The…

Q: 4. An object in isometric view is given as in Figure 3. Draw the object in Third Angle Projection at…

A: An isometric view is given. We need to draw top view, front view and side view

Q: Observed Bearings Length (m) Computed Internal Adjusted Values Line Forward Вack Sta Cor Interior…

A:

Q: 4. A transit is set at point A with elevation 57.4 m, HI = 1.2 m, stadia constant 0.3, stadia…

A: Given data in question  Elevation of point A 57.4 m Height of instrument 1.2 m Angle 4°10' Constants…

Q: Locate the centroid for the area of a quarter circle shown.

A:

Q: REQUIRED: ISOMETRIC DRAWING VEN FIGURE SHOWN TOP VIEW syooing 0.5cm FRONT VIEW RIGHT SIDE VIEW 45

A:

Q: 2. A concrete mixture given in the table below is produced. The true unit weight of concrete is…

A: Consider the above given table True unit weight of concrete is 2370 kg/m3 C} True mix proportion of…

Q: Which command convert discrete objects in polyline Union Join O Polyline Subtract

A: A multiple choice questions is asked, please refer step 2 for detailed explanation and solution.

Q: Draw the Orthographic Projections (Top View, Front View, Side View) For the Shapes Shown Below,…

A: The following orthographic projections for the given shapes are drawn: 1. Top View 2. Front View 3.…

Q: Correctly Dimension the object using datum dimensioning

A: To show the datum referencing of the drawing

Q: Problem 2: The diagram shows a 1 m ruler, pivoted at its midpoint. At what distance x from the…

A: Given data - L = 1 m  Find out - At what distance x from the left-hand end of the ruler must the 10…

Q: The coordinates of centroid for the following section is 150 mm - 20 mm 20 mm 20 mm 300 mm 500 mm

A:

Q: Write a short note on:  Aligned dimensioning. Unidirectional dimensioning.

A: In this system of dimensioning, the dimensions are written along the same direction in the entire…

Q: Use Scale ( 1:1 ), for the front and side views shown draw the isometric projection 22 19 38 Ф 18 22…

A: Given Data :

Q: The tensions in the supporting cables AC and BE are 50N and 70 N. respectively. A load of 10 kg is…

A:

Q: Find the centroid of X and Y in tabular form.

A: A centroid is a point on the body on which the mass of a body is uniformly distributed. If the body…

Q: Draw the 3 Principal Views of the object (units in cm) 5.0 3.0 1.5 R=1.0 1.5 ↓ 1.0 3.0 -2.5 2.0

A: I have draw  Top view.  Front view

Q: 6kN 2 kN\m 3 kN D 6kNm A B A CA 6m

A:

Q: *24 Solve Prob. 2-3 with a = 10ft, b = 15 ft. 2-5. Solve Prob. 2-3 with a = 75 1,b = 20f. Probs.…

A:

Q: Q) Draw the following with scale 2:1: 1. Front Sectional View on A-A 2. Side View 3. Top Sectional…

A:

Q: 40 15 60 90 10 45 07 30

A: The Top view is:

Q: Using engineering graphics and drafting concepts . Draw the isometric view of the given orthographic…

A:

Q: Subject: Engineering Drawing or AutoCAD Instruction: Draw the 2D Orthographic Projection (Front,…

A: Hand made drawing are attached as mentioned in question.

Q: Derive the Trapezoidal rule for multiple segments. Also show a graphical sketch.

A:

Q: Calculate the area between offsets 1 and 10 in Figure 8.10 where these offsets, scaled. from the…

A:

Professional survey

A professional survey is a systematic questionnaire that the target audience fills out online, usually by filling out google forms. Professional surveys can vary in length and format. The data is stored on a website and the testing tool usually provides a certain level of data analysis in addition to a professional expert review. Several professional online survey softwares are present worldwide like, SoGoSurvey, SurveyGizmo, SurveyMonkey, Qualtrics, and so on.