Q1/A motor having a suitable control circuit develops a torque given by the relation Tm = a w² + 4 %3D where a is positive constant. The motor is used to drive a load whose torque is expressed as: - T = c w + 3 where c is positive constant. The total inertia of the rotating masses is J a) Under these conditions, the motor can be starting? b) Calculate the equilibrium operating speed.

Q1/A motor having a suitable control circuit develops a torque given by the relation Tm = a w² + 4 %3D where a is positive constant. The motor is used to drive a load whose torque is expressed as: - T = c w + 3 where c is positive constant. The total inertia of the rotating masses is J a) Under these conditions, the motor can be starting? b) Calculate the equilibrium operating speed.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Question 1: For the electromechnanical system given below: a) Draw the detailed block diagram of the system. b) Take M = 0 kg and find the system transfer function (the input is V, and the output is w). R. Vr Driver R K, N. Jm, Bm, Jr „Br K, K, Tn Wm Tachogenarator V=K, W, 9 =constant u=N1/N2 <1 Na M. =0 Jtako =0 Btako =0 M
2- I need answer of all sub-parts questions. Thanks The figure shows a simple model of a motor vehicle that can vibrate in the vertical direction while traveling over a rough road. The road surface varies sinusoidally with an amplitude of 0.01 m and a wavelength of 6 m. The vehicle has a mass of 1007 kg. The suspension system has a total spring constant of 40 kN/m and a damping coefficient of 20 kN.s/m. The vehicle average speed is v = 100 km/hr. The objective is to determine the vehicle steady-state displacement amplitude as well as the respective transmitted force. Calculate the resultant frequency ratio of the above model. Calculate the steady state amplitude of the vehicle. Determine the force amplitude that will be felt in the vehicle at the steady-state due to the bumpiness of the road.
2- Figure below provides a pneumatic circuit diagram for a pneumatic system. Obtain the motion step diagram of the circuit diagram. 1.0 2.3 2.2 2.0 1.4 1.3 1.1 2.1 ALA 14) 1 1.3 22 2.3 1.4 MW 1.2
Please show the work to understand the process. AI generated steps have been wrong.
Please answer.
A DISCRETE-TIME system has the poles p1 = -0.1, p2 = 0.4, P3 = 1. Describe the stability of the system. O Stable O Marginally stable Unstable Unknown
(machine dynamıc) In a damped free-vibrating mass spring damper system, the mass is 1.9kg, the spring constant is 7550N/m, the amplitude of the 1st cycle is 0.35 cm, and the amplitude after 5 cycles is 0.07 cm.a) The natural frequency of the systemb) The damping degree of the systemc) Find the freely damped vibration frequency of the system.
PROBLEM: A beam weighs 0.031 Slug and is supported on a dashpot. Assume that the dumping factor is 0.3152 and the normal frequency is 653 grad per second. Condition the system is initially at rest and a velocity of 0.035 furlong per second. What is the: A.) Total stiffness of the spring in pound force per inch B.) Damping Factor in pound force per inch C.) Damped frequency of vibration D.) Initial amplitude E.) The displacement and Velocity after 0.040 minutes
A washing machine has 60 kg mass, and 15 cm tub radius. Machine dries the unbalanced3 kg laundry by rotating with 1000 rpm.a) What would be the dynamic force transmitted to the foundation if there is no vibrationisolation for the machine?b) An isolation with damping ratio 0.1 is applied to the machine. In this case, if thetransmitted force is decreased by 90 % what would be the natural frequency of the machine?c) In this case, what would be the vibration amplitude of the machine?
A manipulator’s end-effector position is calculated as follows:x = q0 cos q1 + l2 cos(q1 + q2),y = q0 sin q1 + l2 sin(q1 + q2),where q0,1,2 represent joint displacements and l2 is a constant positive parameter.Which of the following describes this manipulator:1) This is a robot-manipulator with 3 revolute joints.2) This is a robot-manipulator with 2 revolute and 1 prismatic joints.3) This is a robot-manipulator with 1 prismatic and 3 revolute joints.4) This is a robot-manipulator with 2 revolute joints. A robot’s end-effector’s tool position is defined asx = L1 cos(q1) + q3 sin(q1 + q2)where L1 = const, q1 = q1(t), q2 = q2(t) and q3 = q3(t) with t defining time. Calculate ∂x / ∂q3 1) it is impossible to calculate as the equation for the y and z positions are missing.2) cos(q1 + q2).3) it is impossible to calculate as time is not given.4) sin(q1 + q2).
On rubber wedges modeled as spring and damperelectric motor with mass M placed in damped free vibrationit has been observed to oscillate 6 in 1 second when released, and the degree of damping is known to be 0.15.a) calculate the natural frequency of the system.b) calculate the mass of the engine, given as K=50000N/m.c) Moe imbalance in the rotor while the engine is rotating at 1000 rpmbecause of its value, the engine was observed to vibrate at an amplitude of 4 mm.Calculate the moe imbalance value of the rotor?d) the amplitude of the force transmitted to the ground while the engine is rotating at a speed of 1000 rpmcalculate.
In control system R(S) denotes the input of the system. Select one: True False