Q19. As shown in the image below, the 3.7-Mg four-wheel-drive SUV tows the 1.3- Mg trailer. The traction force developed at the wheels of the SUV is Fp = 12 kN. Determine the tension force (in kN) developed in the coupling, A, between the SUV and the trailer. Neglect the mass of the wheels, and also, the wheels of the trailer are free to roll (no traction). Please pay attention: the numbers may change since they are randomized. Your answer must include 2 places after the decimal point. A FD Your Answer: Answer

Q: The frame is loaded as shown. The 150 lb/ft distributed load is perpendicular to member AC. The…

A:

Q: The spring of modulus k=850 N/m is stretched a distance 6 = 74 mm when the mechanism is in the…

A: Given data:The modulus of spring is K = 850 N/mm

Q: Determine the magnitude of the force P required to maintain the equilibrium of the two bar linkages.…

A: The objective of the question is to find the magnitude of the force P that is required to maintain…

Q: A person pulls on a 500 N desk with a 200 N force acting at 30° angle above the horizontal. The desk…

A: QuestionA person pulls on a 500 N desk with a 200 N force acting at 30° angle above the horizontal.…

Q: A 415 kg safe is hanging from the apparatus below.  Determine the tension in the cable.  Dimension…

A:

Q: Two massless and frictionless pulleys are used to drag a large mass (m = 645 kg) up an inclined…

A:

Q: Q2/ Determine the unstretched length of spring AC if a force P = 80lb cause the angle 0 = 60 for…

A: Solution:

Q: What is the magnitude of the force on the pin at point C? (include units with answer) А. What is the…

A:

Q: PROBLEM: ↑ 4m ↓ Determine 2 3KN 5 KN 5KN B 6KW for ce 0 in 4 KN H 4 KN 2 KN da ANTI ks, к.с E H вс

A:

Q: 1 ft 4 ft A 2 ft 45° X F₁ B 3 ft 5 ft 30° 45° y If F₁ = 300 lb. and F₂ is 250 lb., what are the…

A: Given:The force is .The force is .Consider free body diagram:Here,  is reaction force at A in…

Q: Determine the forces at A and B. The force at A is The force at Bis lb 4 lb &

A: This question is based on the concept of classical mechanics on force balancing.

Q: 1.0m 3.0m 0.5m mi PA N, 5. The drawing above shows two objects on a board supported at two…

A: Given: m1=40kgm2=20kgm3=10kg…

Q: The suspended cylinder has a mass of 95 kg. Determine the x and y components of the reaction at pin…

A:

Q: The 12ft pole AC (negligible mass) lies in the y-z plane and forms a 30° angle with the z-axis. The…

A:

Q: The jib crane is designed for a maximum capacity of 14 kN, and its uniform I-beam has a mass of 270…

A:

Q: 6. Determine the force in each cable needed to support the flowerpot whose weight is 10ON とれ В 6 m 4…

A: The position vector is used to describe the location of a body. When it comes to characterising a…

Forming and Shaping

Metal forming is a category of metalworking process through which the material can be given the desired shape and size by subjecting it to plastic deformation, where the component undergoes bulk deformation process upon application of loads. Unlike the shearing and machining process, the material does not undergo up to a failure point as indicated in the stress-strain curve. Hence, the stresses induced during the forming process are greater than yield strength but less than the failure strength of the material. The process does not lead to the loss of material, so it can be said to be an economical process. During forming, the material is subjected to tensile forces, compressive forces, bending, and shearing loading conditions. The material should possess the property of ductility to undergo the forming process.