Q17: A fully-controlled three-phase bridge rectifier circuit is modified by placing a commutating diode across the highly inductive load (load current is continuous and level). Draw the waveform of the output voltage and calculate the mean value of the output voltage for a-90" and 380 V L-L three phase AC supply voltages.

Q17: A fully-controlled three-phase bridge rectifier circuit is modified by placing a commutating diode across the highly inductive load (load current is continuous and level). Draw the waveform of the output voltage and calculate the mean value of the output voltage for a-90" and 380 V L-L three phase AC supply voltages.

Electricity for Refrigeration, Heating, and Air Conditioning (MindTap Course List)

10th Edition

ISBN:9781337399128

Author:Russell E. Smith

Publisher:Russell E. Smith

Chapter12: Electronic Control Devices

Section: Chapter Questions

Problem 4RQ: What is the difference between a diode and rectifier?

See similar textbooks

Similar questions

3 Given the bridge-type full-wave rectifier circuit shown 220V 60Hz 220V:Es Es D1 D2 D3 D4 The load resistor is 220 and the transformer average current is 300mA. Determine: (a) Average value, RMS value, and frequency of load voltage VRL. (b) Average current and PIV of each diode. RL
A single-phase full-wave bridge rectifier circuit is fed from a 220 V, 50 Hz supply. It consists of four diodes, a load resistance 20 Q and a very large inductance so that the load current is constant. What is the average or dc output voltage?
In the blow figure.(need handwritten only ,otherwise downvote.)
Be a single-phase half-wave rectifier with an RL load. The sinusoidal input voltage has a frequency of 60 Hz and the value of R = 10 ohms. What is the value of L for the current extinction angle to be 270°. Tip: use Puschlowski's abacus.
A full-wave rectifier uses 2 diodes. The internal resistance of each diode is 20 Q. The transformer RMS secondary voltage from centre tap to each end of the secondary is 50 V and the load resistance is 980 Q. Mean load current will be
.Draw a full-wave rectifier circuit (using a diode bridge) and predict the output voltage signal when the input is a sinusoidal signal with amplitude 10 V (p p). Use the previous full wave rectifier to create a peak detector with a 2 V ripple.
A certain unfiltered center-tapped full wave rectifier is powered by a 120 Vrms, 60 Hz power system. The peak value of the output voltage under loaded conditions is 30 V. The capacitance value is 2000 uF, load current of 2A, determine the following: 4. DC load voltage Ripple factor C.
H.W:- For a single phase half wave uncontrolled rectifier if the input supply voltage is (v= 310 sin314t), at frequency (f= 50 Hz). Then determine the followings:- Vm. Vmean- i. Draw the rectifier circuit. un %3D ii. Draw the input and the output voltages waveforms. iii. Determine the mean and rms values of the output voltage. s Ec iv. If the load is (R=10 S), then determine the mean and rms values of the current. 2019
In the given Full Wave Center tapped Rectifier circuit, a step down transformer gives an RMS voltage as 110v/11-0-11 V is used with R1-1 Kn. Assume diode as Germanium. a) Find Input Voltage D, Vin b) Find Peak Output Voltage. c) Find Average Output Voltage. d) Find Current through the load resistor. eelee
I need the answer quickly
Design a full-wave bridge type power supply. Design the transformer, filter and regulator section. For the rectifier part, choose diode with appropriate PIV rating. Use standard values for your design. The output dc voltage should be 7.5 V and the Maximum output power be 20 mW. Use the topology below as reference
A fully controlled, single-phase bridge rectifier is powered from an ideal 220V, 50Hz source. The rectifier is triggered with a trigger angle of 60 degrees and provides a smooth current of 50A to the load at the output. According to this: a) Draw the waveform of the output voltage in scale and calculate the average value of the output voltage. Combine the average voltage signal with the output voltage wave signal. Show on the same figure. b) Draw the waveforms of the thyristor currents, the gap diode current and the current drawn from the source in scale. c) Calculate the value of the filter inductance used at the output when the ripple in the load current is 3A. (Do the operations by showing the output voltage shapes and areas on the figure. The answers should be in the system and order in the solved examples.)