Answered: Q16. A mug is to be made from alumina.…

Engineering

Mechanical Engineering

Q16. A mug is to be made from alumina. Which forming method would be most suitable?

Welding: Principles and Applications (MindTap Course List)

8th Edition

ISBN:9781305494695

Author:Larry Jeffus

Publisher:Larry Jeffus

Chapter12: Flux Cored Arc Welding Equipment, Setup, And Operation

Section: Chapter Questions

Problem 20R: Why must a flux form a less dense slag?

See similar textbooks

Related questions

Q: Determine the setting for a straight spur gear having 46 teeth of module 4 mm.

A: Given Data⇒ Straight spur gear : Number of teeth(t)=46 teeth Module(d)=4 mm

Q: 1. Choose the example of good vibration * Guitar Seismic Bullet Train Physiotherapy tools 2. Choose…

A: The desirable vibrations are known as good vibrations and the undesirable vibrations are known as…

Q: 11. At injection pressure of 150 bar a spray penetrat ion af 25 cm in 20 milliseconds is obtained.…

Q: 1. In a turning operation, the diameter of the work- piece is 2 inches (50 mm), and it rotates at…

Q: If P =600 lb, determine the angle alpha so that the resultant of the system is purely vertical.…

Q: an advertising panel erected on uneven ground is supported by the EF and EG guy lines. If the force…

Q: A steel cable with nominal diameter 25 mm as shown in Table Q2(a) is used in a construction yard to…

Q: Q3 A car A is travelling along a straight path, while a lorry B is travelling along a circular path…

A: Given Data The velocity of car A is:VA=150+X=150+2=152 km/h The acceleration of car A is: aA=7000…

Q: H. If the values of F = 25 kN and L = 2.5 m, determine the axial forces in members BE and DG using…

Q: Which of the following is the best example of engineering control? A. noise-cancelling headphones

Q: 3. The liquids shown in figure (13-W1) in the two arms are mercury (specific gravity=13-6) and…

A: Data given- Specific gravity = 13.6 Height of mercury column = 2 cm

Q: (a) Determine the pressure difference between pipes A and B shown in Figure Q2 (a) when a, b and c…

Q: A piece of aluminum is pulled in tension from its original length of 202 mm with a stress of 172…

Q: For gear-and-shaft system shown, both shafts AB and CD have a diameter of 1.2 in. Pulley A is…

Q: 2. Given: The piston rod of the hydraulic cylinder C imparts a constant acceleration to pin A of as…

Q: A vertical force P of magnitude 18 kips is applied at a Point C located on ti column. Knowing that y…

Q: (iii) What is the strain of brass rod of length 250mm which is subjected to a tensile load of 50kN…

A: Given : Length L= 250 mm load P = 50 KN Change in length L1 = 0.5 mm

Q: A multi-fluid manometer shown in Figure 1 is used to measure the pressure in a water tank…

Q: The lift of a wing, Fug, is a function of wingspan, W, chord length, H, surrounding air density, p,…

A: For solution refer below images.

Q: 2. An air conditioner using refrigerant-134a as the working fluid and operating on the ideal vapor-…

Q: Determine the location of the shear center O of a thin-walled beam of uniform thickness having the…

Q: Calculate normal and shear strains at the center

Q: Solve the following questions: 1-The distance yB = 6 m and the magnitude of the force F = 227 N.…

Q: (b) Water flows from a pressurized tank through a pipe and rises to the surrounding as shown in…

A: For the given arrangement A = 6 m, B = 3 m, h = 10 m To determine a) The pressure in the tank…

Question

PLEASE ANSWER QUICKLY

Q16. A mug is to be made from alumina. Which forming method would be most suitable?
A. Melting
B. Welding
C. Machining
D. None of the above

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

9) Tubes can be produced by ___________ process. a. Extrusion. b. Drawing. c. Milling. d. Forging.
Q.4- Write (True) or (False) and correct the wrong sentences for the following: 1. Chills are used to increase the heating rate of metal. 2. Motion of job is forward rotary in broaching operation. 3. The upset type of forging makes increment in the diameter of the workpiece. (1-2) Option 1 4. The torch size of (GTAW) process is larger than other (PAW) process. 5. Only two perpendicular components of cutting force act on the tool in case of oblique cutting. 6. The semicentrifugal casting, is used for casting articles of symmetrical shape about vertical axis. 7. In planer machine tool, workpiece remains stationary and tool reciprocates. 8. Boring is performed on the inside diameter of an existing hole. 9. In grinding processes, small grit sizes used to grind soft materials and permit larger material removal rates. 10. Side rake angle on tools is provided to control chip flow.
Q) give reasons it is preferred to coat steel with zn rather than with cu.
What is hot work?
Manufacturing
7. - is used for water pipes, machine tool castings, transmission housing, engine blocks, pistons and stove castings. A. Pig Iron (Iron Ore) 8. B. Wrought iron C. Cast iron D. Steel ---------------- has a Brinell hardness number of 150 to 220 (no alloys) and 300 to 600 (alloyed) A. Pig Iron (Iron Ore) B. Wrought iron C. Cast iron D. Steel 9. is used to make nails, rivets, gears, structural steel, desks, hoods, fenders, chisels and hammers. D. Steel A. Pig Iron (Iron Ore) B. Wrought iron C. Cast iron
11. Orientation of two circles with the same center. 12. Press fitting a pin/ shaft to a hole results to . fit. 13. AISI designation for free cutting steel. 14. The permissible variation of sizes. 15. The element contained in all classes of stainless steel.
need handwritten explained properly
Q.2- Answer two of the following: a) State the types of sheet metal bending process and compare (in table) between them. b) What the Difference between brazing and soldering? (Compare in table). c) Compare (in table) between shaping and planing operations.
Comparing the processes of tube drawing and tube sinking: a tube sinking use a mandrel b tube sinking preciously controls the inside diameter c tube drawing uses a mandrel d tube drawing is used with thick walled tubes
3 The example for forming process is ___________. a. Gas welding b. Extrusion c. Tempering d. Die Casting
What is hard slag?