Q14) A 65-kg beef carcass (k=0.47 W/m °C and a=0.13x10-6 m²/s) initially at a uniform temperature of 37°C is to be cooled by refrigerated air at -6°C flowing at a velocity of 1.8 m/s. The average heat transfer coefficient between the carcass and the air is 22 W/m2°C. Treating the carcass as a cylinder of diameter 24 cm and height 1.4 m and disregarding heat transfer from the base and top surfaces, determine how long it will take for the center temperature of the carcass to drop to 4°C. Also, determine if any part of the carcass will freeze during this process.

Q14) A 65-kg beef carcass (k=0.47 W/m °C and a=0.13x10-6 m²/s) initially at a uniform temperature of 37°C is to be cooled by refrigerated air at -6°C flowing at a velocity of 1.8 m/s. The average heat transfer coefficient between the carcass and the air is 22 W/m2°C. Treating the carcass as a cylinder of diameter 24 cm and height 1.4 m and disregarding heat transfer from the base and top surfaces, determine how long it will take for the center temperature of the carcass to drop to 4°C. Also, determine if any part of the carcass will freeze during this process.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A steam power plant is located in the northern part of the country. Steam in the plant flows steadily through a 0.162-m diameter pipeline from the steam generating unit (SGU) to the steam turbine. At the SGU end, the steam conditions are determined to be P = 4 MPa, t = 400°C, h = 3,235.1 kJ/kg, and specific volume = 0.118 m³/kg. At the steam turbine end, the conditions are found to be P = 3.5 MPa, t = 392°C, h = 3,109.4 kJ kg, and specific volume = 0.231 m³/kg. Heat loss from the pipeline is 6.80 kJ/kg. Determine the steam mass flow rate in kg/s.
Moist air of 0.1 kg/s enters a heating coil at t= 15°C, d = 10 gkg., and exits it at t= 50°C. Determine h at the outlet and the kW of heating required during the process. (c,=1.01kJ/kg K. p = 101325 Pa) 79. BI UA.EEEN A T
I need the answer as soon as possible
Engr. Dizon, a mechanical engineer, is planning to construct a cooling water pond in Laguna for a power plant. The power plant is known to discharge 20 m/s of cooling water. Estimate the required surface area (in hectares) of the pond if the water temperature is to be lowered from 45 C at its inlet to 35.5 C at its outlet. Assume specific heat of water is 4.186 kJ/kg-K, and an overall heat transfer coefficient of 0.0412 kJ/s-m2-K. Round off your answer to the nearest whole number.
A long counter-flow heat exchanger cools water from 40°C to 10°C by passing the water via the inner tube through an enclosure of cold fluid. The water is flowing through a 3-cm diameter tube at a rate of 0.27 kg/s. The cold fluid enters the enclosure at −10°C and has a convection coefficient of 1200 W/m².K. The mass flow rate of the cold fluid and its specific heat are 1.2 kg/s and 1340 J/kg-K, respectively. (a) Assuming the flow is fully developed, find out the convection coefficient of the water flow. (b) What is the length of the heat exchanger? 1554 W/m²K 2 21.9m Water Cold Fluid
Can you assist me with the HW problem.
Please answer
A heat engine operates between two reservoirs at 200°C and 20°C. One-half of the work output of the heat engine is used to drive a compressor of a refrigeration system, which is used to cool the chiller in a factory. (i) Apples with average mass of 500 g are dropped into the chiller at a rate of 10 pieces per minute, cooling from 20°C to 4°C. Determine the heat transfer rate of the apples.
A steam condenser operates at 61 cm of Hg vacuum. The steam enters the condenser with a moisture content of 87%. Cooling water is supplied to the condenser at a temperature of 20 C with a terminal difference of 5 C. The water velocity of water inside the tube is to be limited to 2.5 m/s when using 2.5 cm outside diameter tubes whose thickness is 1.75 mm. The overall heat transfer coefficient of the tubes could be approximated by the equation U = 1213.4(v1/2), W/(m2-C) where v is the water velocity in m/sec. Determine: 1. The required mass flow of cooling water, kg/s 2. The required capacity of the circulating pump, liter per second 3. The Logarithmic Mean Temperature Difference, C 4. The required Number of tubes 5. The required length of tubes, (m), and number of passes
A 5m copper tube is heated externally to 100degC. Air is heated by passing it through the 40mm diameter tube, h=0.03375kW/m²-K. The air enters the tube at 20degC and leaves at 88degC. The average air velocity is 8m/s. Calculate the heat transfer in kW
Engine oil (C, =2100 J/kg · °C) is to be heated from 20°C to 60°C at a rate of 0.3 kg/s in a 2-cm-diameter thin walled copper tube by condensing steam outside at a temperature of 130°C (hɛ =2174 kJ/kg). For an overall heat transfer coefficient of 650 W/m2 · °C, determine the rate of heat transfer and the length of the tube required to achieve it.
Air at a dry bulb temperature of 40℃ and a wet bulb temperature of 20℃ is first heated in a heater to a dry bulb temperature of 90℃. Then it is passed through a bed of apricot slices to dry them. The air exiting from the top of the apricot bed is at a dry bulb temperature of 60℃. Clearly show the various paths of the process on a psychrometric chart! Determine the amount of moisture removed, in grams of water/second from the apricot bed!