Q10/ In a single integration DM scheme, the voice signal is sampled at a rate of 64 kHz. The maximum signal amplitude is 2 volts. Voice signal bandwidth is 3.5 kHz. Determine the minimum value of step size to avoid slope overload and granular noise power. (ans. AVmin= 0.6872mV, Nq = 8.6 mW)

Q: Draw the amplitude shift keying signal. b) Draw the frequency shift keying sign. c) Draw the phase…

A: a) Draw the amplitude shift keying signal.   b) Draw the frequency shift keying sign.   c) Draw the…

Q: 1. Draw a Load Line Transistor Characteristic Curve with details- 2. Draw the circuit of a…

A:

Q: Draw the hierarchy of digital modulation techniques.

A: DIGITAL MODULATION: The process of embedding a digital data message into amplitude or magnitude,…

Q: What are different step in typical ASIC design flow.

A: To verify a design we write verification module and  test bench to check that it meet…

Q: Design the given circuit at Ico = 2 ICSAT and VCEQ = 2 Vcc use Vcc = 28 volts, IcsAT = 10 milli…

A: " Since you have posted a question with multiple subparts, we will solve the first three subparts…

Q: Q3/ Design (64-1) multiplexer by using (8-1) active low multiplexers.

A:

Q: RF = 30KN, R₁ 01 = 5KQ and +15V ? in

A: Please refer the attached images for the complete answer

Q: Design the given circuit at Ico = ½ ICSAT and VCEQ = ½ Vcc use Vcc = 28 volts, ICSAT = 14 milli…

A: In this solution we discuss about the BJT biasing circuit.

Q: b) Determine the input waveforms 4 and that pridaced the output waveforms in Figure bellow. NAND…

A:

Q: 5. Can you modify the Astable Oscillator to have a Duty Cycle of 10%? Be sure to justify your…

A:

Q: a) Choose laas for an output DC bias level Vopc = Vozpcy= 3.00 V. b) Determine the voltage gain of…

A:

Q: A. Draw the maximum point detector circuit and sketch the output waveform for the input signal of…

A:

Q: 1) What does tdi and ta2 represent in Pulse signal transmission lines experiment? What is the…

A: It is asked the names of td1 and td2 in pulse signal transmission lines experiment. Also we need to…

Q: Whas is the circuit diagram of linear voltage regulator for fixed output voltage using IC78xx and…

A: Voltage regulator- Voltage regulator is a device which provide a fixed voltage as an output for…

Q: Design the given circuit at Icq = ½ ICSAT and VCEQ = ½ Vcc use Vcc = 20 volts, IcsAT = 10 milli…

A:

Q: Draw the schematic of a modulo-6 syncrhonous counter (counting sequence is 010, 110, ...). The…

A:

Q: The current output of a successive approximative type ADC is showing as 110011. If the reference…

A:

Q: 3. What happens if the inverting & non-inverting i/p of the comparator interchanged?

A: As per guidelines, we can only provide the solution of one question in multiple type of questions.…

Q: 1.N-channel MOSFET is faster than P-channel mosfet. True False 2.MOSFET have threshold voltage of…

A: The solution is given below

Q: What is the difference between Q-point and Q-point stability?

A:

Q: For the NMOSFET in the circuit below, K = 4.00mA/V^2, VTHN = 1.00V, l = 0V^-1, and VIN = 4.00V. a.…

A:

Q: For the circuit shown in Figure B19a, Ve 20V Rc 3kQ RB = 10k 2 VCE VBB=3V Figure B19a i) Sketch the…

A:

Q: Two low pass signals, each band limited 4 KHz, are to be time multiplexed into a single channel…

A: Given data, Band limit BL=4 kHz Frequency fs=10 kHz

Q: Q4. A) Compare the operation of a series modulator eircuit with a collector modulator circuit in AM…

A: Series Modulator Here the modulating signal is applied to the emitter follower. This emitter…

Q: In a PCM system, channels of 3 KHz bandwidth are used. If the uniform quantizer has 128 number of…

A: Channel capacity is defined is the maximum amount of data rate at which information can be reliably…

Q: What is PWM (Pulse Width Modulation), and how is it used in microcontroller applications? Provide…

A:

Q: Discuss common mode rejection ratio. Common mode rejection is desirable or undesirable?

A: The objective is to determine common mode rejection ratio.

Q: Calculate the third harmonic distortion in the Colpitts oscillator under small signal conditions.

A: The Colpitts oscillator is a particularly good circuit for producing fairly low distortion sine wave…

Q: For a single-tone modulating signal of 5 kHz and a carrier frequency of 600 kHz, list the…

A:

Q: What are the main advantages of Delta Modulator over PCM?

A: Pulse code modulation (PCM) and delta modulation (DM) are both extremely efficient. However, delta…

Q: Q4/ What is the exciter? Explain the static AVR loop. What is the function of AVR loop?

A: We need to explain about exciter and we also need to explain the static AVR loop and  the function…

Q: Suggest a demodulator circuit to detect the data signal from the Phase shift keying modulated signal…

A: A signal obtained is called a carrier signal. A Carrier signal with information is also called a…

Q: 4. Draw the circuit structure of a TCR. By changing the firing angle of thyristors, how can we…

A:

Q: Outline the circuit condition for using the supernode technique.

A: Suppose any of the branches in the network has only voltage source, then it is slightly difficult to…

Q: c) (i) i. Describe the precaution you would take in selecting the sampling interval ii. How may the…

A: (i) Precaution in selecting the sampling interval, The main precaution is that the sampling…

Q: 1-) demodulating by multiplying the AM signal with the carrier signal 2-) demodulation using…

A: As per our guidelines we are supposed to answer only one question. Kindly repost other questions as…