Q10: Determine the maximum load P (in kN) that can be applied if the normal stress on plane AC must not exceed 18 MPa.

Q: This still doesnt answer how to get points 2,  2', and 1', so how did you get it?

A: Itis asked to explain how the state points 2, 2' and 1' are obtained

Q: cker mechanism rocking angle of 70 degrees. What are the lengths of the 4 bars in inches

A: A four-bar crank-rocker mechanism rocking angle of 70 degrees. What are the lengths of the 4 bars in…

Q: S (-36mm) is correct but total distance traveled (166.04 mm) was marked wrong can you help me?

A:

Q: For the given isometric drawing, draw the corresponding top, front and right side views

A: According to the given data A isometric view of a object  We need to draw  The corresponding top,…

Q: If the main scale reading(mm) and vernier scale reading (division) are 29 and 18 respectively for a…

A: Solution:

Q: Forces and moments are scalar Forces are moments are vector quantities.

A: Forces and moments are both physical quantities that can be used to describe the behavior of objects…

Q: If the main scale reading(mm) and vernier scale reading (division) are 16 and 9 respectively for a…

A: It is a precision instrument with a low least count, and is used to take sub-millimeter dimensions…

Q: I o2s+lo4 s+1. .96 2. L'st ++T?

A:

Q: Draw Front and Side and top with all dimensions please

A: Find Draw the front, side, and top of the object with dimensions.

Q: Draw chalk diagram of all sections

A: To draw section views

Q: What are the different types of force? Applied Tension Gravitational Spring Air Resistance Normal…

A: (I) Force has been classified on the basis of contact which is as follow 1. Contact force:- These…

Q: 1.00 1.38 3.38 38 2.00

A: Select the correct statement about the notation circled in green and marked as letter D. Assume all…

Q: what is the scale if a line is 10 inches but is  drawn 5 inches long.

A: Finding scale if a line is 10 inches but is  drawn 5 inches long.

Q: Help , Handwritten only. No Chatgpt

A:

Q: 1500# 1500# 1500# 1500# 12' K I

A: In this problem, following steps will be taken 1. Determine the reactions at the supports.' 2. Using…

Q: Select the correct statement about the notation circled in green and marked as letter C. Assume all…

A:

Q: IF y = u² + 3u² & u = 2x Find dy dx

A:

Q: PART VI. Given that f(x,y) = (x +y)/2k, where x=-1,1,2 and y= 0,2,4 1. Find k 2. Find the marginal…

A:

Q: A 70 kg skier that moves from rest at A is shown in Figure Q2. Suppose friction can be neglected…

A: Given:m=70 kgθ=30°θ=40°Height AB=12mTo find:-1) Velocity VB2) The istance S

Q: Can you show the work but written out please so I can see the steps better.

A:

Q: If a force doubled, impulse will triple. True or false

A:

Q: now please answer question 2 and 3 please

A: This question is based on the concept material science. As per the guidelines we are subjected to…

Q: The headless type of set screw are known as screws * ....... grub O machine O rag О Сар The only…

A: Isometric drawing is the three-dimensional drawing of the object. It has two types - 1. Isometric…

Q: Part C - Maximum allowable axial force for fixed-and-free-end support If the cylindrical column is…

A:

Q: An inclined limb manometer is used for measurement of flow rate reads 0.535 L/s. The true value of…

A:

Q: 0 = 0° A

A:

Q: Indicate whether the terms are like or unlike. - 322, 5z? ... The two terms 5z and - 3z are

A: The two terms 5z2 and -3z2 are like terms.

Q: Which of the following statement is correct? Select one: Speed is a Vector & Velocity is a Scalar…

A: Speed is a scalar quantity – it is the rate of change in the distance travelled by an object.

Q: . Circle the letter corresponding to the view on the right that shows the result of rotating the…

A: According to the given details provided, we need to identify the view on the right that shows the…

Q: TOP FRONT SIDE

A: GIVEN DATA ISOMETRIC VIEW GIVEN WE HAVE TO DRAW ORTHOGRAPHIC VIEWS OF GIVEN FIGURE

Q: Q1: Use scale (1:1), draw the front, top & side views of shape shown below. (50 M)

A: Orthographic Projection It is a form of presenting a three-dimensional object into Two dimensional.…

Q: Draw the Isometric drawing of the given orthographic projections below. Use drawing scale to fit the…

A:

Q: Draw Front and Side and top with all dimensions please

A: Draw the top view and side view first as shown in the below attached image:

Q: Find the vertical force component for the figure 800 N y 50°

A: Given data :-  Force F = 800 N  Theta = 50°  Find :-  Vertical component = ?

Q: 4C) Concurrent forces ... O a. act on the same line. O b. None of the these O C. act on the same…

A: A set of point forces is considered concurrent in the event that all the lines of activity of…

Q: Dimensions and magnitude mean size, for example the diameter of the wheels of a mountain bike etc.…

A: The dimensions help us find the size of the object. Suppose dimension of plate is given , it will…

Q: Draw Front and Side and top with all dimensions please

A: According to the question we need to determine  Orthographic projection views.

Forming and Shaping

Metal forming is a category of metalworking process through which the material can be given the desired shape and size by subjecting it to plastic deformation, where the component undergoes bulk deformation process upon application of loads. Unlike the shearing and machining process, the material does not undergo up to a failure point as indicated in the stress-strain curve. Hence, the stresses induced during the forming process are greater than yield strength but less than the failure strength of the material. The process does not lead to the loss of material, so it can be said to be an economical process. During forming, the material is subjected to tensile forces, compressive forces, bending, and shearing loading conditions. The material should possess the property of ductility to undergo the forming process.