Q1. The following data refer to the O.C.C of a D.C separately excited generator at 1000 rpm. Field current in A 0.2 0.4 0.6 0.8 1 1.2 Amature voltage in V 75 100 145 178 195 204 The machine is now connected as a shunt generator with a total field resistance of 200 2 and driven at 1000 rpm. Estimate graphically: (i) the voltage to which the generat or will build up at no load. (ii) the armature, field and load currents when the teminal voltage is found to be 150 V. Neglect the effect of armature reaction and brush drop and assume armature resistance Rato be 0.8 2. (iii) Finally estimate the steady state armature current when the machine terminals are shorted.

Q1. The following data refer to the O.C.C of a D.C separately excited generator at 1000 rpm. Field current in A 0.2 0.4 0.6 0.8 1 1.2 Amature voltage in V 75 100 145 178 195 204 The machine is now connected as a shunt generator with a total field resistance of 200 2 and driven at 1000 rpm. Estimate graphically: (i) the voltage to which the generat or will build up at no load. (ii) the armature, field and load currents when the teminal voltage is found to be 150 V. Neglect the effect of armature reaction and brush drop and assume armature resistance Rato be 0.8 2. (iii) Finally estimate the steady state armature current when the machine terminals are shorted.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A long shunt compound generator has armature shunt field and series field resistances of 0.05, 100 and 0.3 ohms respectively. When supplying a load of 8 kw at a terminal voltage of 250 V, the input power supplied by the driving motor to the generator is 10.4 kw. Calculate a. the generated emf b. the generator efficiency. Write the solution completely.
A dc shunt generator has a critical field resistance of 400 Q2 at 1200 rpm. Now if the speed of the generator is increased to 1800 rpm what is the change in the critical resistance?
A 3-phase 50 Hz I.M. has a rated torque = 16.7 N.M and maximum torque = 40.5 N.M. If its rated speed = 910 R.P.M, the speed at :maximum torque will be R.P.M 578.280 R.P.M 421.640 R.P.M 590.160 None O
i. Briefly describe the 5 major types of DC generators according to the manner in which their field flux is produced.
the armature of a 12 pole wave wound dc shunt generator has 50 slots with 12 conductors per slot. the generatoris running at a speed of 625 rpm and supplies a resistive load of 15 ohm at a terminal voltage 350v. the armature and the field reisitance are0.5 ohm and 70 ohm respectively. find the armature current,generated emf and flux per pole
q10
× 4:03 K s.eng.ruh.ac.lk □ Û 8. Figure 4 shows the core of a simple dc motor. The magnetization curve for the metal in this core is given by Figure 5 and Figure 6. Assume that the cross-sectional area of each air gap is 18 cm² and that the width of each air gap is 0.05 cm. The effective diameter of the rotor core is 4 cm. L It is desired to build a machine with as great a flux density as possible while avoiding excessive saturation in the core. What would be a reasonable maximum flux density for this core? ii. What would be the total flux in the core at the flux density of part (i)? iii. The maximum possible field current for this machine is I A. Select a reasonable number of turns of wire to provide the desired flux density while not exceeding the maximum available current. Flux Density, B (T) 2.8 སྤྲ ཤཱ ཀ ཀཱ བྷ ཀ ཡཱཾ བ ་ 1.2 1.0 0.4 0.2 4-48cm Figure 4 0 10 20 30 40 50 100 → Depth 4 cm -0.05 cm 200 300 500 1000 2000 Magnetizing Intensity, H (A.turns/m) Figure 5 Magnetization curve…